Acer 41L1700-786-7A Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

background image

41L1700-786-7A

英文

15

ERROR MESSAGE & POSSIBLE SOLUTION

CABLE NOT CONNECTED :

1. Check that the signal-cable is properly connected , If the connector is

loose, tighten the connector’s screws.

2. Check the signal -cable connection pins for damage.

INPUT NOT SUPPORT :

Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table(See page 18).

«
...
14
15
16
17
18
...
»

Содержание 41L1700-786-7A





















Отзывы:

Нет отзывов

Похожие инструкции для 41L1700-786-7A

UltraView iAP1700

Бренд: I-Tech Страницы: 28

Бренд: Mackie Страницы: 39

MultiSync LCD1515

Бренд: NEC Страницы: 2

MultiSync LCD1515

Бренд: NEC Страницы: 40

MULTISYNC LCD1510+

Бренд: NEC Страницы: 12

Бренд: IEE Страницы: 22

UltraView iAP1000AV

Бренд: I-Tech Страницы: 1

Бренд: 4D systems Страницы: 6

Бренд: Maxent Страницы: 1

Бренд: Jimi Страницы: 33

Бренд: AOC Страницы: 50

Бренд: Raymarine Страницы: 3

Бренд: Oromed Страницы: 70

Бренд: AOC Страницы: 66

Бренд: Uniden Страницы: 32

MultiSync E224F

Бренд: NEC Страницы: 38

MultiSync EA245WMi-2

Бренд: NEC Страницы: 30

Бренд: Dell Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды