Acer 12000 Скачать руководство пользователя страница 27

Страница: 27 / 30

System Board

1-27

Table 1-4

System Error Messages

Message

Action

Diskette Drive Controller Error
or Not Installed Floppy Disk
Controller Error

Check and connect the control
cable to the diskette controller.

Diskette Drive Error

Check the CMOS settings in
Setup and the diskette drive cable
connections.

Diskette Drive A Type
Mismatch Floppy Drive A
Error

Run Setup and select the proper
drive type.

Diskette Drive B Type
Mismatch Floppy Drive B
Error

Run Setup and select the proper
drive type.

ECC Facility Fail

Contact your dealer.

Equipment Configuration Error

Modify DRAM configuration to
agree with one of the options in
Table 1-3.

Expansion ROM Allocation
Failed

Contact your dealer.

Hard Disk Controller Error

Run Setup.

Hard Disk 0 Error IDE Primary
Channel Master Drive Error

Check all cable connections.
Replace hard disk.

IDE Primary Channel Slave
Drive Error

Check all cable connections.
Replace hard disk.

Hard Disk 1 Error IDE
Secondary Channel Master
Drive Error

Check all cable connections.
Replace hard disk.

IDE Secondary Channel Slave
Drive Error

Check all cable connections.
Replace hard disk.

Hard Disk 0 Extended Type
Error

Run Setup.

Hard Disk 1 Extended Type
Error

Run Setup.

IRQ Setting Error

Run Setup.

Содержание 12000































Результаты поиска

Содержание 12000

Отзывы:

Похожие инструкции для 12000

Бренды по названию

Популярные бренды

Acer 12000, Руководство пользователя

Результаты поиска

Содержание 12000

Отзывы:

Похожие инструкции для 12000

Бренды по названию

Популярные бренды