background image

 

ACE INDUSTRIAL PRODUCTS 

WALL MOUNTED FUME EXTRACTOR 

MODEL 73-501 

 
 

INSTALLATION MANUAL 

 

READ AND SAVE THESE INSTRUCTIONS. 

 

SAFETY WARNINGS & CAUTIONS 

FAILURE TO OBSERVE THE FOLLOWING PRECAUTIONS COULD RESULT IN SERIOUS INJURY, INCLUDING 
DEATH IN EXTREME CASES.  SAVE THESE INSTRUCTIONS. 
 

WARNING: (EXPLOSION HAZARD) 

This machinery is not suitable for collection of combustible metal as listed in NFPA 484, which includes: 

Aluminum

,

 

Titanium

,

 Magnesium

Lithium

Niobium

, and 

Zirconium

.

 

 

WARNING:  
(VOC’S & AIRBORNE MICROBES) 

The filters used in this unit will remove solid particulate ONLY, and will not eliminate Volatile Organic Compounds (VOC’s) 
or airborne microbes (bacteria, mold & viruses) that may be a health hazard.  Failure to observe the presence of such 
fumes could cause serious illness or death. 

 

CAUTION: (STRONG VACUUM) 

Care must be taken to avoid personal injury by not allowing hose inlet to contact any body area such as eyes, ears, 
mouth, etc.  

 

CAUTION: (LIFTING)

 

Improper lifting or handling of this unit could cause back injury.   
 

CAUTION: (AIR FLOW BLOCKAGE) 

Since exhaust air leaves the top of this unit, caution should be observed not to mount unit in such a way as to block the 
exhaust. 
 

CAUTION:

 

Some of these items are powered by rotating electrical machinery! Careless or improper use may result in personal injury. 

 

CAUTION: 

Do not look directly into the motor compartment or outlet with the power on or without wearing safety goggles. 
 

MISCELLANEOUS CAUTIONS: 

1.  Use of any attachment not recommended or sold by the air cleaner manufacturer may result in risk of fire, electric 
shock, or injury to persons. 
 
2.  Do not disassemble the air cleaner.  Take it to a qualified serviceman when service or repair is required. Incorrect 
reassembly may result in risk of electric shock or fire. 
 

 

1

Содержание 73-501














Отзывы: