AccuTemp Accu-Steam G2 Series Скачать руководство пользователя страница 35

Страница: 35 / 39

MP5017-2002

Accu-Steam Gas Griddle

6.6 ERROR CODE DISPLAYED

E001 Displayed

Open Temperature Sensor or defective
temperature input on Temperature Control
Board.

E002

Shorted Temperature Sensor or defective input
on the Temperature Control Board.

6.7 FAULT LIGHT ILLUMINATED

When this error is lit an ignition failure of the
appliance has occurred. Following the following
steps:
1.  Turn the appliance off
2.  Verify that your flexible quick connect gas

line is fully engaged to the appliance gas
input connection if applicable.

3. Verify your gas shutoff valve is turned on to

supply gas to the appliance.

4. Once these have been verified and 1 minute

has passed since it was turned off turn the
appliance on.

Fig 6.A

Fault Light

6.8 OVER-TEMP LIGHT ILLUMINATED

When this error is lit an over-temp condition
was sensed and will turn off the appliance

To correct, turn the appliance off and wait
one minute and turn the appliance back on.

If problem persists - call AccuTemp Service

Fig 6.A

Over-Temp Light

(Heat light will also be

illuminated in normal

operation)

Содержание Accu-Steam G2 Series








































Результаты поиска

Содержание Accu-Steam G2 Series

Отзывы:

Похожие инструкции для Accu-Steam G2 Series

Бренды по названию

Популярные бренды

AccuTemp Accu-Steam G2 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Accu-Steam G2 Series

Отзывы:

Похожие инструкции для Accu-Steam G2 Series

Бренды по названию

Популярные бренды