manualshive.com logo in svg

Accurex XRUBS-140, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Accurex XRUBS-140 Скачать руководство пользователя страница 11

Steel Grease Fan

11

Parts List

CAUTION

A fan manufactured with an explosion resistant motor 
does not certify the entire unit to be explosion proof. 
Refer to UL Listing mark for the fans approved usage.

CAUTION

La présence d’un moteur antidéflagrant sur un 
ventilateur ne garantit pas que tout l’appareil est 
antidéflagrant. Pour connaître les emplois autorisés 
de l’appareil, voir son marquage de conformité UL.

Each fan bears a manufacturer’s nameplate with model 
number and serial number embossed. This information 
will assist the local representative and the factory in 
providing service and replacement parts. Before taking 
any corrective action, make certain unit is not capable 
of operation during repairs.

NOTE

For replacement, the windband, vertical supports, 
drain trough and curb cap with mounting holes comes 
as one complete assembly.

Vertical Supports

Clean-Out Port

Curb Cap with
Mounting Holes

Breather Tube

Motor Cover

Motor

Motor Pulley

Non-Stick Wheel

Horizontal Supports

Windband

Hoodband

Shaft Pulley

Belt(s)

Bearings

Vibration Isolators (4)

(not visible)

Fan Shaft

Disconnect Switch

Содержание XRUBS-140













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды