10
GB
StreamPunch
TM
Ultra/Ultra MP
8. DIE SET USER MANUAL
The die sets for the StreamPunch Ultra are intended to work with
multiple paper sizes and sheet feed directions. In order to
accommodate different sheet sizes this die set must be configured to
the correct number of punching pins and the die stop must be set to
the proper position. The die label contains information on the common
paper punching sizes, for the uncommon sizes please refer to Table 1.
Glossary
LEF- Long Edge Feed- Indicates that the paper is being fed through
the machine so that the longer side of the sheet will be punched.
SEF- Short Edge Feed- Indicates that the paper is being fed through
the machine so that the shorter side of the sheet will be punched.
Statement (STMT) Paper- 8.5" X 5.5"
Legal Paper- 8.5" X 14"
Ledger Paper- 11" X 17"
Pin Numbering
Die punching pins are numbered sequentially starting from the handle
end. Figure 8.1 shows a 47 hole coil die (404757) as an example. All
square and round hole die sets follow the same pin numbering format.
Figure 8.1 Coil Die Set Pin Numbering
Figure 8.2 Pressure Bar Removal
To remove punch pins from the StreamPunch Ultra first turn the two
Quarter Turn Fasteners counter clockwise to release the pressure bar.
Remove the pressure bar and set aside.
Figure 8.3 Pressure Bar
Figure 8.3 Pin Removal
Lift up and remove the desired pins according to Table 8.1. Store pins
in the pin storage tray inside front door of machine making sure pins
cannot be dropped, damaged or lost while removed.
Figure 8.4 Replace Pressure Bar
Replace the pressure bar by lining up dowel pin holes with exposed
dowel pins. Hold pressure bar so that it is seats completely over dowel
pins and then rotate Quarter Turn Fasteners clockwise until a click is
felt to lock pressure bar in position.
Important! Make sure pressure bar is attached and both Quarter Turn
Fasteners are in the locked position prior to inserting the die set into
the machine or serious damage can occur to both the machine and die
set.
Dowel Pin
Holes
Dowel Pin Holes
Pin #1
Pin #47
Quarter Turn
Fastener
Pin Removal
Coil
Rnd/Oval
Wire
2:1
Rnd/Sq
Wire
3:1
Rnd/Sq
3 Hole
8mm
3/5/7
Hole
8mm
2/4
Hole
8mm
2/4
Hole
6.5mm
2/4
Hole
SCAN
VeloBind
11 Hole
LTR
VeloBind
12 Hole
A4
CombBind
eWire
Rnd/Sq
US Paper Sizes
Pin numbers to be removed based on paper size and orientation
Ricoh Part Number
404757
404771
404758
404768
404759
404769
404760
404762
404763
404763
404764
404765
404766
404768
404770
404772
LTR LEF
2, 47
1, 23
1, 34
NONE
3H/5H/7H
N/A
N/A
N/A
NONE
N/A
1, 21
1, 34
LTR SEF
7, 42
NONE
5, 31
N/A
N/A
N/A
N/A
N/A
N/A
N/A
NONE
N/A
STATEMENT LEF
7, 42
NONE
5, 31
N/A
N/A
N/A
N/A
N/A
N/A
N/A
NONE
5, 31
LEGAL SEF
7, 42
NONE
5, 31
N/A
N/A
N/A
N/A
N/A
N/A
N/A
NONE
5, 31
LEDGER SEF
2, 47
1, 23
1, 34
NONE
3H/5H/7H
N/A
N/A
N/A
NONE
N/A
1, 21
1, 34
9" x 12" LEF
1, 2, 47
1, 23
1, 34
NONE
3H/5H/7H
N/A
N/A
N/A
NONE
N/A
1, 21
1, 34
9" x 12" SEF
6, 7, 42, 43
3, 21
5, 31
N/A
N/A
N/A
N/A
N/A
N/A
N/A
3, 19
5, 31
12" x 18" SEF
1, 2, 47
1, 23
1, 34
NONE
3H/5H/7H
N/A
N/A
N/A
NONE
N/A
1, 21
1, 34
Coil
Rnd/Oval
Wire
2:1
Rnd/Sq
Wire
3:1
Rnd/Sq
3 Hole
8mm
3/5/7
Hole
8mm
2/4
Hole
8mm
2/4
Hole
6.5mm
2/4
Hole
SCAN
VeloBind
11 Hole
LTR
VeloBind
12 Hole
A4
CombBind
eWire
Rnd/Sq
ISO Paper Sizes
Pin numbers to be removed based on paper size and orientation
Ricoh Part Number
404757
404771
404758
404768
404759
404769
404760
404762
404763
404763
404764
404765
404766
404768
404770
404772
A4 LEF
NONE
NONE
NONE
N/A
N/A
2H/4H
2H/4H
NONE
N/A
NONE
NONE
NONE
A4 SEF
7, 41
4, 21
5, 30
N/A
N/A
1, 4
1, 4
NONE
N/A
N/A
4, 19
5, 30
A5 LEF
7, 41
4, 21
5, 30
N/A
N/A
1, 4
1, 4
NONE
N/A
N/A
4,19
5, 30
A3 SEF
NONE
NONE
NONE
N/A
N/A
2H/4H
2H/4H
NONE
N/A
NONE
NONE
NONE
SRA4 LEF
NONE
NONE
NONE
N/A
N/A
2H/4H
2H/4H
NONE
N/A
NONE
NONE
NONE
SRA4 SEF
6, 7, 41, 42
4, 21
4, 5, 30, 31
N/A
N/A
1, 4
1, 4
NONE
N/A
N/A
4, 19
4, 5, 30, 31
SRA3 SEF
NONE
NONE
NONE
N/A
N/A
2H/4H
2H/4H
NONE
N/A
NONE
NONE
NONE
*For CombBind 20H configuration pull Pin Number 1
Table 8.1 Pin Removal Guide
The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the StreamPunch
Ultra can accept. For standard offering dies not found in the chart no pin adjustment is necessary.
