background image

Manual PCIe-DIO-24HS PCI Express Digital I/O Card 

Warranty

 

 
Prior to shipment, ACCES equipment is thoroughly inspected and tested to applicable specifications. However, 
should equipment failure occur, ACCES assures its customers that prompt service and support will be available. 
All equipment originally manufactured by ACCES which is found to be defective will be repaired or replaced 
subject to the following considerations. 
 

Terms and Conditions

 

 
If a unit is suspected of failure, contact ACCES' Customer Service department. Be prepared to give the unit 
model number, serial number, and a description of the failure symptom(s). We may suggest some simple tests 
to confirm the failure. We will assign a Return Material Authorization (RMA) number which must appear on the 
outer label of the return package. All units/components should be properly packed for handling and returned 
with freight prepaid to the ACCES designated Service Center, and will be returned to the customer's/user's site 
freight prepaid and invoiced. 
 

Coverage

 

 
First Three Years: Returned unit/part will be repaired and/or replaced at ACCES option with no charge for labor 
or parts not excluded by warranty. Warranty commences with equipment shipment. 
 
Following Years: Throughout your equipment's lifetime, ACCES stands ready to provide on-site or in-plant 
service at reasonable rates similar to those of other manufacturers in the industry. 
 

Equipment Not Manufactured by ACCES

 

 
Equipment provided but not manufactured by ACCES is warranted and will be repaired according to the terms 
and conditions of the respective equipment manufacturer's warranty. 
 

General

 

 
Under this Warranty, liability of ACCES is limited to replacing, repairing or issuing credit (at ACCES discretion) 
for any products which are proved to be defective during the warranty period. In no case is ACCES liable for 
consequential or special damage arriving from use or misuse of our product. The customer is responsible for all 
charges caused by modifications or additions to ACCES equipment not approved in writing by ACCES or, if in 
ACCES opinion the equipment has been subjected to abnormal use. "Abnormal use" for purposes of this 
warranty is defined as any use to which the equipment is exposed other than that use specified or intended as 
evidenced by purchase or sales representation. Other than the above, no other warranty, expressed or implied, 
shall apply to any and all such equipment furnished or sold by ACCES. 

Содержание PCIe-DIO-24H



















Отзывы: