background image

30

2) Address setting of each unit: when the address mode is set to be centralized controller address

mode. The address setting value range is 01~16. The setting method is: 

Under off state of the unit, press Function and Mode buttons at the same time for 5s to enter setting 

interface of wired controller 

address. LCD displays address sequence. Press ▲ or ▼ button to adjust the 

address sequence and then press Enter/Cancel button to confirm. The setting value will be memorized 

after power failure. The detailed setting is as shown in the Figure below: 

Figure 2-7-13 

When the address is set, the wired controller can be removed and connect the centralized controller 

to the indoor mainboard. Then connect the required units to realize centralized control of these units; 

Note: 

When centralized controller is to be connected, set the address mode into centralized controller

address mode through wired controller. Long-distance control address mode can not be set; 

The  unit  addresses  in  the  same  network  must  be  different,  otherwise,  communication

malfunction will occur and the unit can not work normally; 

When centralized controller is to be connected, the unit address range is 1-16. Only 16 sets of

unit in maximum can be connected 

The code and model of wired controller is as below:

Содержание H-Series


































Отзывы: