background image

507043-03

Page 1 of 9

Issue  1739

Save these instructions for future reference

INSTALLATION INSTRUCTIONS

4AC13/14/16 SPLIT SYSTEM AIR 

CONDITIONER

 

(P) 507043-03

*P507043-03*

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in 

manuals, be alert to the potential for personal injury or death.

Improper installation, adjustment, alteration, service 

or maintenance can cause property damage, personal 

injury or loss of life. Installation and service must be 

performed by a licensed professional installer (or 

equivalent), service agency or the gas supplier.

 WARNING

Installation or repairs made by unqualified persons can 

result in hazards to you and others. Installation MUST 

conform with local building codes and with the National 

Electric Code NFPA 70/ANSI C1-1993 or current edition 

and Canadian Electrical Code Part 1 CSA .

 WARNING

Table of Contents

Safety Precautions ......................................................2

Installation ...................................................................2

Electrical Connections .................................................4

Start-Up Procedure......................................................5

System Operation ........................................................6

Homeowner’s Information ...........................................9

These instructions are intended as a general guide and 

do not supersede national, state or local codes in any 

way.
These instructions must be left with the property owner.

NOTE

These instructions and warranty are to be given to the 

owner or prominently displayed near the indoor air 

handler unit.

NOTE TO INSTALLING DEALER

This product contains a chemical known to the State 

of California to cause cancer, birth defects or other 

reproductive harm.

 WARNING

Содержание 4AC13










Отзывы: