background image

39

Q: 

How do I stop my device from turning on and off too quickly in AUTO mode?

A:

 The figure set in the BUFFER section will determine how easily the device can turn off again 

once it has been triggered on. 

Access this section under SETTINGS by clicking the sprocket icon at the top right. Set a buffer 
number X. Once your device is triggered ON, it would require X amount to fall below your trigger 
point for it to trigger OFF again. The lower the buffer number is set to, the easier it will be for 
the device to trigger back to OFF. If set to zero, the device will trigger ON and OFF immediately 
whenever the trigger point is crossed. This may cause the device to turn on and off quickly if the 
climate fluctuates back and forth. Increase the buffer number to help reduce this from occurring. 
Please also check your high and low triggers point which can all activate concurrently. Turn off any 
trigger points that are not in use.

FAQ

Q: 

Why is my humidifier not turning on or off when I programmed it to do so under AUTO mode? 

A:

 If this is occurring in AUTO mode for humidity triggers, please note that the HIGH HUMIDITY 

trigger turns the device ON when the humidity number you have set is exceeded. If you want the 
device to turn OFF when the humidity number you have set is exceeded, please set this using 
the LOW HUMIDITY trigger instead. 

Typically, the HIGH HUMIDITY trigger is used with dehumidifiers which should turn on when the 
humidity gets too high. The LOW HUMIDITY trigger, which turns on the device when the humidity 
gets too low, is more suitable for humidifiers. 

All the four high and low temperature and humidity trigger points can activate concurrently 
so turn off any triggers that are not in use. Also, check that the buffer number you have set is 
appropriate as it may delay the program from turning your device on and off. Lastly, please check 
if you have any active programming on the app under the ADVANCE TAB which can override any 
control programming.

Содержание CONTROLLER 79













































Отзывы: