Absolare Push-Pull Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 15

Absolare Push-Pull Скачать руководство пользователя страница 4

4

ABSOLARE Push-Pull Mono Amplifier User Manual 1.2

1. General Description

The Absolare Push-Pull Mono Amplifier is a transformer coupled, zero feedback,
monoblock power amplifier, supplied in matched pairs for stereo amplification. It
features an all tube, point-to-point construction signal path. It is available in both
transformer balanced (XLR) and unbalanced (RCA) input versions.

2. Safety Issues and Warnings

-

Be sure the voltage setting of the unit matches the applied voltage to power

input.

Operating voltage is fixed and must only be changed by an authorized service

agent.

-

Do not touch tubes while operating.

Tubes are extremely hot devices and also

contain very high voltages.

-

Do not open bottom covers.

There are no user serviceable parts inside the units.

-

Do not operate the amplifier without an output load.

4

– 8Ω speaker or

equivalent load should be connected to speaker terminals when the Amplifier is
operating.

«
...
2
3
4
5
6
...
»

Содержание Push-Pull
















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды