Absco Industries SKILLION CPSN2 Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

Absco Industries

Assembly Instruction Manual

ABSCO SKILLION CARPORT

MODEL: CPDN2

5.50mW x 5.50mD x 2.37mH

Model: CPSN2

25/11/22

15

DOWNPIPE

It can be fit to either end of the rear beam, make
a decision based on site specific factors.

Cut a round hole 51mm dia in one end of the
rear edge beam. The can be done by drilling a
series of 3mm holes and knocking it out or by
metal holesaw. It won’t be visible when finished.

Fit the galvanised gutter drop RWG17 from the
top down into the hole.

Drill two 3 mm holes through the underside of
the end beam and into the flange of the gutter
drop and then fasten using two pop rivets. Use
water proof sealant around the hole inside the
beam.

Join the top three pieces of the down pipe
assembly, RWG02 + RWG13 + RWG02 with PVC
solvent welding cement. Position over the gutter
drop and align with post.

Drill two 3 mm holes through both sides of the
PVC elbow and into the gutter drop and then
fasten with two tek screws.

Fit one end of downpipe RWG14 with the elbow
RWG01 at trim the other end to the desired
height. Fix with PVC solvent welding cement.

Bend two 270 x 25 mm flat strips ZACO126 to
shape around the downpipe and to the sides of
the post and fasten with tek screws.

Immediate maintenance required!

Clean down all roof and beam internal areas

of metal filings from drilling operations and

self drilling screws.

If not cleaned these will cause discolouration

and corrosion to roof sheets and galvanised

framing sections, see warranty for more details

RWG01

RWG02

RWG02

RWG14

1880 mm

ZACO126

RWG13

1200 mm

ZACO126

RWG17

RWG02

SIDE

BEAM

REAR

BEAM

Inset from
side beam
110 mm

110

«
...
13
14
15
16
17
...
»

Содержание SKILLION CPSN2





















Отзывы:

Нет отзывов

Похожие инструкции для SKILLION CPSN2

CombiTent PARTY TENT SEMI PRO

Бренд: Dancover Страницы: 10

Бренд: Woods Страницы: 8

Бренд: LEINER Страницы: 11

Бренд: Mec Страницы: 7

Бренд: Bonga Страницы: 18

Бренд: Polaris Страницы: 3

Бренд: SJK Страницы: 2

Бренд: RioOutdoors Страницы: 34

Бренд: NRS Relief Страницы: 2

Бренд: Hilleberg Страницы: 16

Бренд: Nordcap Страницы: 2

Бренд: GenTent Страницы: 4

Бренд: Millenium Страницы: 22

Бренд: Outer Limits Страницы: 10

Бренд: Axley Страницы: 3

Бренд: Eureka Страницы: 2

Monterey 6 14'x8'

Бренд: Coleman Страницы: 2

Outdoorsman 9280-108

Бренд: Coleman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды