ABONG SEBRINGVILLE 3157826 Скачать руководство пользователя страница 1

Страница: 1 / 97

A clock is a precision mechanical instrument containing many

slowly moving parts. There are over a hundred points of contact

where friction works to bring it to a stop.
Take your time assembling this kit, and pay attention to the

details. Great pains have been taken to craft these instructions

to ensure your success. If there are any steps that seem unclear,

please let us know.
Before you begin, check that there are no missing or damaged

pieces in the kit. A parts list is provided to help identify each

piece.
Finally, read through all the instructions before you begin. This

will help you understand how each piece fits into the finished

clock.

WALL CLOCK KIT

SEBRINGVILLE

DAMAGED OR MISSING PARTS?

email: [email protected]

Made in Canada by

ABONG, Inc

5-775 Woodlawn Road W

Guelph, ON N1K 1Y7

WARNING!

CHOKING HAZARD - CONTAINS

SMALL PARTS. NOT RECOMMENDED

FOR CHILDREN UNDER 3 YEARS

Содержание SEBRINGVILLE 3157826


































































































Результаты поиска

Содержание SEBRINGVILLE 3157826

Отзывы:

Похожие инструкции для SEBRINGVILLE 3157826

Бренды по названию

Популярные бренды

ABONG SEBRINGVILLE 3157826, Руководство пользователя

Результаты поиска

Содержание SEBRINGVILLE 3157826

Отзывы:

Похожие инструкции для SEBRINGVILLE 3157826

Бренды по названию

Популярные бренды