Ablerex MSRT-Pro 1KVA Скачать руководство пользователя страница 25

Страница: 25 / 28

8.3. DCE (Dry Contact) card

8.3.1. The pin assignments of 10-Pin Terminal

：

UPS on Bypass mode (Bypass)

Utility Normal (Normal close contact)

Utility Normal (Normal open contact)

Inverter On

Battery Low

Battery Bad or abnormal

UPS Alarm

Common

Shutdown UPS po) signal

Shutdown UPS negative(-) signal

8.3.2. The shutdown function will be activeated, after a +6~+25Vdc is put

between pin 9 and pin 10 for 5 seconds.

8.3.3. The capacity of each relay contact is 40Vdc/25mA.
8.3.4. Installation

Position

：

Optional Slot.

8.3.5. Flexible signal output for N.C.(Normal Close) or N.O.(Normal Open)

contact by shorting pin1-2 or pin2-3 form JP1-5.

8.3.6. The shutdown function will be enabled in 1 minute after blackout occurs

if the pin1-2 of both CN1 and CN6 are shorted by cap. Or, the shutdown
function can only be enabled by pin9-10 of CN3 if the pin2-3 of both
CN1 and CN6 are shorted by cap.

1 2 3 4 4 5 6 7 8 9 10

8.4. SNMP Cards

8.4.1. SNMP/WEB

card

8.4.1.1 For installation, please refer to the user’s manual attached with the

card.

8.4.1.2 Installation

Position

：

Optional Slot

8.4.2. SNMP card of Megatec

8.4.2.1 For installation, please refer to the user’s manual attached with the

card.

8.4.2.2 Installation

Position

：

Optional Slot

Содержание MSRT-Pro 1KVA





























Результаты поиска

Содержание MSRT-Pro 1KVA

Отзывы:

Ablerex MSRT-Pro 1KVA, Руководство пользователя, Страница: 25 / 28

Результаты поиска

Содержание MSRT-Pro 1KVA

Отзывы: