manualshive.com logo in svg

ABLE Systems Ap863, Руководство пользователя

Поделиться
Скачать
ABLE Systems Ap863 Скачать руководство пользователя страница 9

Ap863 Users’ Guide Page 9 of 18

be holding charge as well as expected, it may be worn out and should be replaced by a new one.
Please consult the factory for further details and recommended battery treatment.

During battery charging, the printer may become quite warm.  This can crease the paper within the
mechanism.  The system designer may wish to feed out some paper before printing begins, either
controlled from the host, or by the user pressing the paper feed button.

4.7 

VEHICLE ADAPTOR POWER PACK

The Direct Vehicle Adaptor Power Pack is designed to be operated from a st12V ( Negative
Earth) vehicle power source.  It must be connected on a cable loom which is capable of supplying
10A and have a 10A in-line fuse in the positive connection.

Electrical Specification

Input Voltage Range:

+11v to +18v

(with over-voltage spike protection)

Supply Current Requirement:

2mA 

( Printer in Sleep Mode )

( typical )

100mA 

( Printer in Idle Mode 

)

3A average

( Printer Printing

)

10A peak 

( Printer Printing 

)

N.B. The average and peak current requirements can be adjusted by firmware control codes.
See the Programmer Guide or contact Able Systems for details.

Printer Side Connector:

Molex Mini-Fit Junior Series 2 way
Part Number:

39-01-2021

Fitted with Molex Crimp Terminal
Part Number

39-00-0041

User Side Connector:

Molex Mini-Fit Junior Series 2way
Part Number:

39-01-2020

Recommended Molex Crimp Terminal (for the above connector)
Part Number: 

39-00-0039   (2 off required)

4.8 

OEM 5-7.5V DC ADAPTOR PACK

The Direct ‘Raw DC’ Input Power Pack is designed to be operated from a 5V to 7.5V voltage source
which is capable of supplying the primary power for the printer. It must be connected on a cable loom
which is capable of supplying 10A and have a 10A in-line fuse in the positive connection.

Electrical Specification

Input Voltage Range:

+5.0V to +7.5V (without any over-voltage or reversal protection)

Supply Current Requirement:

2mA 

( Printer in Sleep Mode )

( typical )

100mA 

( Printer in Idle Mode 

)

3A average

( Printer Printing

)

10A peak 

( Printer Printing 

)

N.B. The average and peak current requirements can be adjusted by firmware control codes.
See the Programmer Guide or contact Able Systems for details.

Printer Side Connector:

This product has a cable  with pre-stripped and tinned ends ready for
connection to the host PSU.

Содержание Ap863



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды