Kruk
Stelknop
Elektronisch display
Pedaal
Vergrendelingsknop
Voetband
Pootjes
Crank
Tension knob
Electronic display
Pedal
Push pin
Foot strap
Legs
1. Remove contents from box.
2. Pull legs in opposite direction until locking button “snaps” into locking receiver. (see figure A)
3. Attach electronic display to the pedal exerciser by sliding the loop over the tension knob around
the frame (see figure B)
Attention: Only attach the multi function display to this adhesive label!
4. Insert tension knob on top of pedal exerciser and turn clockwise to tighten. The tension knob will
increase/decrease the amount of tension on the pedal exerciser. Tighten/loosen to a level that
feels comfortable.
5. You can set the width of the foot strap through the 2 adjustment holes. (see figure C)
1. Haal het apparaat uit de verpakking.
2. Klap de pootjes naar buiten open tot deze in de vergrendeling ‚vastklikken‘. (zie afbeelding A)
3. Bevestig het elektronische display met de lus om de stelknop. (zie afbeelding B)
Let op: Klem het multifunctionele display alleen op deze sticker!
4. Om de trapweerstand in te stellen, gebruikt u de stelknop aan de bovenzijde van de fietstrainer
die u langzaam met de wijzers van de klok meedraait. Draai de stelknop strakker aan of losser
totdat u een prettige weerstand hebt ingesteld.
5. U kunt de breedte van de voetband verstellen aan de hand van de 2 afstelgaten.
(zie afbeelding C)
To fold, depress push pin and fold leg inward. Repeat for second
leg. (see figure D).
Om de fietstrainer in te klappen, drukt u de vergrendelingsknop
in en klapt u de pootjes naar binnen. Doet dit aan beide zijden
van de fietstrainer. (zie afbeelding D)
If the display does not come on
or reads incorrectly, the battery
requires replacement. To replace
the battery slide the lid on the back
of the display down, replace the
underlying battery and set the
display back on.
Let op: Niet op de
fietstrainer staan.
Vermijd schade: belast
de pedalen niet met
een te hoog gewicht.
Attention:
Do not
stand on the pedal
exerciser! Do not put
too much weight on the
pedals, otherwise the
pedal exerciser may be
damaged.
Wanneer het display niet meer goed
werkt of verkeerde gegevens toont, moet
de batterij worden vervangen. Als u de
batterij wilt vervangen, schuift u het klepje
aan de achterkant van het display naar
beneden. Vervang de batterij en zet het
display weer aan.
1. MODE (Red Button): this control allows you to select a particular function.
To Start, press and hold the Red Button for 4 seconds. The LED will display the different
functions. If you do not select a function, the unit will automatically shut off.
2. To select a function, wait until the 4 seconds set up is complete. Push the Red Button and the
arrow will move through the functions. When the desired function is selected, simply use the
pedal exerciser and the unit will analyse the exercise.
3. COUNT (CNT): counts the number of steps.
4. TIME: indicates duration of training.
5. CALORIE (CAL): indicates the amount of calories burned.
6. REPS PER MINUTE (RPM): automatically calculates the number of repetitions per minute.
7. SCAN: automatically reviews the results of all functions.
To reset the display to zero, press the Red Button (RESET) 3 seconds.
1. MODE (rode knop): met deze knop selecteert u een bepaalde functie. Houd de rode knop 4
seconden ingedrukt. Op het LED display verschijnen de verschillende functies. Als u na
activering geen keuze maakt, wordt de eenheid automatisch uitgeschakeld.
2. Wacht 4 seconden tot de set up gereed is en selecteer een functie. Door het indrukken van de
rode knop, loopt de pijl langs de verschillende functies. Nadat u de gewenste functie hebt
geselecteerd, begint u met uw training. De fietstrainer analyseert automatisch de traininig.
3. TELLER (CNT): telt het aantal trapbewegingen.
4. TIJD (TIME): geeft de trainingsduur weer.
5. CALORIEËN (CAL): geeft het totaal aantal verbrande calorieën weer.
6. OMWENTELINGEN PER MINUUT (RPM): berekent automatisch het aantal herhalingen per minuut.
7. SCAN: geeft automatisch de resultaten van alle functies weer.
Om de display weer op nul te zetten, drukt u 3 seconden op de rode knop (RESET).
ASSEMBLY INSTRUCTIONS
FUNCTION AND DISPLAY DESCRIPTION
FUNCTIE EN BESCHRIJVING VAN HET DISPLAY
BATTERY REPLACEMENT
BATTERIJ VERVANGEN
FOLDING
INKLAPPEN
MONTAGEHANDLEIDING
NL
Aids to daily living
Aids to daily living
figure A
afbeelding A
figure B
afbeelding B
figure C
afbeelding C
figure D
afbeelding D
folded
ingeklapt
1. Remove contents from box.
2. Pull legs in opposite direction
until locking button “snaps”
into locking receiver. (see
figure A).
3. Attach digital display to the
peddler by sliding the loop
over the tension knob recep-
tacle located on the clasp
on the back of the display
attaches to the peddler fra-
me. (see fig. B)
Attention: Only at-
tach the multi-fun-
ction display to this
adhesive label!
4. Insert tension knob on top of
peddler and turn clockwise
to tighten. The tension knob
will increase/decrease the
amount of tension on the
peddler. Tighten/loosen to a
level that feels of tension on
the peddler. Tighten/loosen
to a level that feels.
assembly instruction
Tension knob
Swivel shaft
Legs
Digital Display
Footrest plate
Footrest pad
Hinge
figure A
figure B
figure C
Attention: Do not stand
on the pedal trainer! Do
not put too much weight
on the pedals, otherwise
the pedal trainer may be
damaged
1. Remove contents from box.
2. Pull legs in opposite direction
until locking button “snaps”
into locking receiver. (see
figure A).
3. Attach digital display to the
peddler by sliding the loop
over the tension knob recep-
tacle located on the clasp
on the back of the display
attaches to the peddler fra-
me. (see fig. B)
Attention: Only at-
tach the multi-fun-
ction display to this
adhesive label!
4. Insert tension knob on top of
peddler and turn clockwise
to tighten. The tension knob
will increase/decrease the
amount of tension on the
peddler. Tighten/loosen to a
level that feels of tension on
the peddler. Tighten/loosen
to a level that feels.
assembly instruction
Tension knob
Swivel shaft
Legs
Digital Display
Footrest plate
Footrest pad
Hinge
figure A
figure B
figure C
Attention: Do not stand
on the pedal trainer! Do
not put too much weight
on the pedals, otherwise
the pedal trainer may be
damaged
1. Remove contents from box.
2. Pull legs in opposite direction
until locking button “snaps”
into locking receiver. (see
figure A).
3. Attach digital display to the
peddler by sliding the loop
over the tension knob recep-
tacle located on the clasp
on the back of the display
attaches to the peddler fra-
me. (see fig. B)
Attention: Only at-
tach the multi-fun-
ction display to this
adhesive label!
4. Insert tension knob on top of
peddler and turn clockwise
to tighten. The tension knob
will increase/decrease the
amount of tension on the
peddler. Tighten/loosen to a
level that feels of tension on
the peddler. Tighten/loosen
to a level that feels.
assembly instruction
Tension knob
Swivel shaft
Legs
Digital Display
Footrest plate
Footrest pad
Hinge
figure A
figure B
figure C
Attention: Do not stand
on the pedal trainer! Do
not put too much weight
on the pedals, otherwise
the pedal trainer may be
damaged
1. Remove contents from box.
2. Pull legs in opposite direction
until locking button “snaps”
into locking receiver. (see
figure A).
3. Attach digital display to the
peddler by sliding the loop
over the tension knob recep-
tacle located on the clasp
on the back of the display
attaches to the peddler fra-
me. (see fig. B)
Attention: Only at-
tach the multi-fun-
ction display to this
adhesive label!
4. Insert tension knob on top of
peddler and turn clockwise
to tighten. The tension knob
will increase/decrease the
amount of tension on the
peddler. Tighten/loosen to a
level that feels of tension on
the peddler. Tighten/loosen
to a level that feels.
assembly instruction
Tension knob
Swivel shaft
Legs
Digital Display
Footrest plate
Footrest pad
Hinge
figure A
figure B
figure C
Attention: Do not stand
on the pedal trainer! Do
not put too much weight
on the pedals, otherwise
the pedal trainer may be
damaged
