3-10
Chapter 3
Second Boot Device:
Description is the same as the
First Boot Device,
the default setting is
HDD-0
.
Third Boot Device:
Description is the same as the
First Boot Device,
the default setting is
CDROM
.
Boot Other Device:
Two options are available: Enabled or Disabled. The default setting is
Enabled
. This setting allows the
BIOS to try three kinds of boot devices that are set from the above three items.
Swap Floppy Drive:
This item can be set as Enabled or Disabled. The default setting is
Disabled
.
When this feature is enabled,
you don’t need to open the computer case to swap the position of floppy disk drive connectors. Drive A
can be set as drive B and drive B can be set as drive A.
Boot Up Floppy Seek:
When the computer boots up, the BIOS detects if the system has an FDD or not. When this item is
enabled, if the BIOS detect no floppy drive, it will display a floppy disk drive error message. If this item
is disabled, the BIOS will skip this test. The default setting is
Disabled
.
Boot Up NumLock Status:
On:
At boot up, the Numeric Keypad is in numeric mode. (Default Settings)
Off:
At boot up, the Numeric Keypad is in cursor control mode.
Disable Unused PCI Clock:
This option disables the clock of PCI slot that is not in use.
Security Option:
This option can be set to System or Setup. The default setting is
Setup
. After you have created a password
through PASSWORD SETTING, this option will deny access to your system (System) or modification of
computer setup (BIOS Setup) by unauthorized users.
SYSTEM:
When you choose System, a password is required each time the computer boots up. If the
correct password is not given, the system will not start.
SETUP:
When you choose Setup, a password is required only when accessing the BIOS Setup. If the
correct password is not given, you can’t enter the BIOS setup menu.
To disable security, select
Set Supervisor Password
at main menu and then you will be asked to enter the
password. Do not type anything and just press the
<Enter>
key and it will disable security. Once security
is disabled, the system will boot and you can enter the
BIOS setup menu
freely
NOTE:
Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
BE7 Series
Содержание BE7
