Abit AMD ATHLON KV8 PRO Скачать руководство пользователя страница 45

Страница: 45 / 80

BIOS Setup

3-17

Back to Advanced Chipset Features Setup Menu:

LDT & PCI Bus Control:

Click <Enter> key to enter its submenu:

Upstream/Downstream LDT Bus Width:

This item allows you to select LDT Bus Width.

LDT Bus Frequency:

This item allows you to select LDT Bus Frequency.

PCI1/PCI2 Master 0 WS Write:

Two options are available: Enabled or Disabled. The default setting is

Enabled

. When

Enabled,

writes to

the PCI bus are executed with zero wait state (immediately) when PCI bus is ready to receive data. If it is
set to

Disabled

, the system will wait one state before data is written to the PCI bus.

PCI1/PCI2 Post Write:

Two options are available: Enabled or Disabled. The default is

Enabled

, When

Enable

, data transmission

from CPU to PCI bus are buffered and compensate for the different speed between CPU and PCI bus. If it
is set to

Disabled

, data transmissions are not buffered and CPU must wait until the data transmission is

complete and then start another transmission cycle.

Back to Advanced Chipset Features Setup Menu:

Memory Hole:

When set to [15M–16M], the memory address space at 15M-16M will be reserved for ISA expansion
cards that specifically requires this setting. This makes the memory from 15MB and up unavailable to the
system. Leave this item to its default setting.

Vlink Data Rate:

This item can let you select the Vlink Data Rate between northbridge and southbridge.

User’s Manual

Содержание AMD ATHLON KV8 PRO

















































































Результаты поиска

Содержание AMD ATHLON KV8 PRO

Отзывы:

Похожие инструкции для AMD ATHLON KV8 PRO

Бренды по названию

Популярные бренды

Abit AMD ATHLON KV8 PRO, Руководство пользователя

Результаты поиска

Содержание AMD ATHLON KV8 PRO

Отзывы:

Похожие инструкции для AMD ATHLON KV8 PRO

Бренды по названию

Популярные бренды