ISSUED 02-27-23
PAGE 2 OF 2
2300RS-2-00.DWG
2300RS
1" Extension
*
*
Approx.
2-5/8"
2-5/8"
1"
WALL PORTION INSTALLATION:
1. Measure distance from pivot centerline to wall (Dim. "A").
2. Determine door width (Dim. "B").
3. Use table below to locate magnet box on wall (Dim. "C").
a. Example : Dim. "A" = 10" Dim. "B" = 42" Result Dim. "C" = 39".
b. If Dim. "A" or Dim. "B" Falls between dimensions listed in the table
below, allow for difference.
Example : Dim. "A"= 7" Dim. "B" = 36" Estimated Dim."C" = 33-7/16"
c. If Dim. "A" and Dim. "B" intersect in the shaded area,
DO NOT INSTALL
magnet box.
The degree of door opening will not allow for proper alignment between armature
and wall magnet.
4. Suggested vertical location is on top rail approximately 5" from top of the door.
5. Check degree of door opening shown in table and coordinate with door closer and
other door hardware.
6. Total projection of door hardware must not be more than 5-5/8" on the pull side of door.
If greater, you will need to use additional extensions, sold separately.
7. From corner of wall, measure the appropriate Dim. "C" determined in step 3.
8. Proper electrical wire routing must be done before installing electrical box.
9. The electrical box should be installed with reinforcement to withstand a
minimum 50 lb. pull.
10. Before installing magnetic wall portion, consult " ELECTRICAL DATA" on page 1.
IMPORTANT :
Check that power voltage equals one of the voltages labeled on back of magnet.
DOOR ARMATURE INSTALLATION:
1. Place and center the door armature on the surface of the magnet with the two holes
of the base aligned horizontally.
2. Gently close the door and adjust the angle of the door armature so the base lays flat
against the door.
3. While keeping slight pressure on the door, mark location of door armature through
the two base holes.
4. Drill through the door where the two marks are located with 5/16" drill.
Fasten armature with the (2)10-32 machine screws & sex bolts provided.
For 2-5/8" Door Projection,
use 1" Extension provided
complimentary
C
A
B
NOTE:
1. All dimensions are provided in inches, unless noted otherwise.
2. Additional extensions can be ordered separately to increase the
door armature projection : 3/8", 1/2", 3/4", 1", 2", 4" or 6".
1-3/4"
1-5/8"
41-1/4 86°
41-3/8 89°
41-3/8 92°
41-1/4 95°
41 97°
40-3/4 100°
40-1/4 103°
39-3/4 106°
39-1/8 109°
38-1/2 112°
37-1/2 115°
36-1/2 118°
Dim"C" Deg
26-1/8 117°
27-1/8 113°
27-7/8 109°
28-3/8 105°
28-7/8 101°
29-1/8 97°
29-3/8 93°
29-3/8 89°
29-1/4 85°
Dim "C" Deg
27-1/4 84°
25-1/4 84°
22-5/8 117°
23-5/8 112°
24-3/8 107°
24-3/4 102°
25-1/4 98°
25-3/8 93°
25-3/8 89°
25-3/4 110°
23-7/8 119°
24-7/8 115°
26-1/4 106°
26-7/8 101°
27-1/8 97°
27-3/8 93°
27-3/8 89°
Dim"C" Deg
28
Dim"C" Deg
30
30-7/8 119°
31-7/8 116°
32-3/4 112°
33-1/2 109°
34-1/8 105°
34-5/8 102°
35 99°
35-1/4 95°
35-1/4 92°
35-3/8 89°
35-1/4 86°
Dim "C" Deg
33-1/4 85°
31-1/4 85°
27-3/8 119°
28-3/8 115°
29-1/4 111°
30 107°
30-1/2 104°
31 100°
31-1/4 96°
31-1/4 93°
31-3/8 89°
32 106°
28-1/2 121°
29-5/8 118°
30-5/8 114°
31-3/8 110°
32-1/2 103°
33 99°
33-1/4 96°
33-3/8 92°
33-3/8 89°
Dim "C" Deg
32
34
Dim "C" Deg
36
39-1/4 86°
37-1/4 86°
32 121°
37-1/4 95°
37 98°
36-5/8 101°
36-1/8 105°
35-5/8 108°
34-7/8 111°
34 114°
33 119°
37-1/4 92°
37-3/8 89°
38-1/4 104°
37-3/4 107°
37 110°
36-1/4 113°
35-3/8 116°
34-1/4 129°
39-3/8 89°
39-1/4 95°
39 98°
38-5/8 101°
39-1/4 92°
Dim"C" Deg
38
40
Dim"C" Deg
42
45-1/4 87°
43-1/4 87°
43-3/8 89°
43-1/4 94°
43 97°
42-3/8 102°
41-7/8 105°
41-1/2 108°
42-3/4 100°
40-1/2 111°
39-3/4 114°
38-3/4 117°
43-3/8 92°
44-3/8 102°
43-7/8 105°
43-1/4 107°
42-3/4 110°
42 113°
41 115°
45-3/8 89°
45-1/4 94°
45 97°
44-3/4 99°
45-1/4 92°
Dim "C" Deg
44
46
Dim "C" Deg
48
DIM. "B" (DOOR WIDTH)
2
4
6
8
10
12
14
16
18
20
22
26
Dim.
"A"
24
21-5/8 122°
22-5/8 124° 25 122°
26-1/8 124°
29-5/8 123°
33-1/8 123° 35-3/8 121°
40 118°
37-3/4 120°
2-3/4"
4 5/8"
3"
Magnet Box
Centerline
Pivot
Centerline
Lock Edge
of Door
2300RS ELECTROMAGNETIC DOOR HOLDER, ROCKER SWITCH
SURFACE WALL MOUNT
c