ABB XSeriesG4 Скачать руководство пользователя страница 101

Страница: 101 / 116

5 Troubleshooting

XSeriesG4 Remote Controller User's

manual

2103334 Rev. AB

| 89

Check for a poor cable connection in the cable between the XRC

and the battery pack (J16) and charging source (J17).

Verify that all field wiring screw terminals are tight.

Correct and retest, as necessary.

Verify that there are no other devices that may drop an excessive voltage across them in the power supply circuit (to the

XRC

Correct and retest, as necessary.

Disconnect the charging source cable at the XRC

board J17.

Replace the battery with a known good battery, using the procedure in section 4.6,

Replacing the XRCG4 battery pack

Reconnect the charging source cable to the XRC

board J17.

Measure the voltage at the charging source cable. Measure the voltage at battery pack. Compare voltages. If the

charging source voltage is less than (+) 0.4 Vdc higher than the battery voltage, return to Figure 80:

Power

troubleshooting flowchart

and continue.

Solar panel charging system test

If the system setup includes a solar panel charger connected to the XRC

board, and it is not supplying the required voltage to

the XRC

unit, test the solar panel. The following instructions contain the steps required to do so.

Step-by-step instructions

Check the solar panel angle and direction. In the northern hemisphere, the panel should face due south and in the

southern hemisphere, it should face due north.

Correct and retest, as necessary.

Check the solar panel for any physical damage or obstructions to sunlight. Sunlight obstruction prevents the solar panel

from receiving enough sunlight to charge the installed battery pack.

Clean, correct and retest, as necessary.

The solar panel should be positioned so that it receives the most sunlight. Do not place it in a shaded area.

Correct and retest, as necessary.

Check the solar panel wiring to be certain it is correctly connected to the associated XRC

board termination block J17.

Correct and retest, as necessary.

Measure the solar panel voltage at the connector using a DMM connecting the (+) and (-) leads to the (+) and (-) solar

panel wires. Loaded voltage should be greater than or equal to the specification listed in Table 17.

Table 17: Specifications for solar panels

Panel Max

Volts at
P

Max

Open
Circuit

Load
Resistance

Loaded
Voltage

10 W

16.8 V

21 V

30 Ω 25 W

–18 Vdc

20 W

16.8 V

21 V

15 Ω 25 W

–18 Vdc

30 W

16.8 V

21 V

10 Ω 40 W

–18 Vdc

If the solar panel is not above minimum, replace the solar panel. Return to step 1.

Disconnect the solar panel from the XRC

board.

Set the DMM range to read over 20 Vdc.

Содержание XSeriesG4





















































































































Результаты поиска

Содержание XSeriesG4

Отзывы:

ABB XSeriesG4, Руководство пользователя, Страница: 101 / 116

Результаты поиска

Содержание XSeriesG4

Отзывы: