ABB XIO-00 Скачать руководство пользователя страница 40

Страница: 40 / 207

| XIO USER MANUAL | 2106424MNAB

Figure 4-7: XIO default screen – Entry mode (Advanced view)

To use Ethernet, complete the steps in section

4.3.2 Using the Ethernet ports

first, change to

expert view (section

4.4 Change PCCU to Expert view

), and then proceed to section

4.5

Configure basic XIO parameters

To use USB, remain on the current USB connection, change to expert view (section

4.4

Change PCCU to Expert view

), and then proceed to section

4.5 Configure basic XIO

parameters

4.3.2

Using the Ethernet ports

The XIO Ethernet interface supports local TCP/IP communications and is configured as a 4-port switch

from the factory. A default IP address (

169.254.0.13

) is ready for initial local communication using any

of the 4 ports. All ports are enabled by default.

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды