ABB VT Guard Pro Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 10

ABB VT Guard Pro Скачать руководство пользователя страница 9

9

1VLM000651, Rev.3, en 2014.01.21

6.

Dimensional drawing

7.

Maintenance and service

It is important to keep VT Guard Pro in cleanliness. Special attention should be paid to cleanliness of air-ventilation
gaps. In case, of choked air-ventilation gaps the device should be disconnected from the circuit (both functional and
diagnostic part), then the air-ventilation gaps can be cleaned by brush or compressed air. Other preventive
maintenance is not needed.

Any repairs must be done only by authorized personnel.

Manufacturer does not take responsibility for improper
device functioning in case of unauthorized servicing

Choked gaps may cause failure of appliance.

8.

Warranty

The manufacturer warranty is 24 months since the day of putting the apparatus into operation but not longer than 36
months since the day of purchase.

9.

Disposal

The device contains electronic parts. It should be disposed in electronic-waste recycling centre according to the local
law.

«
...
7
8
9
10
»

Содержание VT Guard Pro











Отзывы:

Нет отзывов