ABB VSN300 Скачать руководство пользователя страница 13

Страница: 13 / 69

- 13 -

000460AG

2 - Characteristics

odels and range of equipment

The device dealt with in this manual is available in a single version

suitable for all countries of installation.

The list of compatible converters and the functions released for each

inverter model is indicated in a separate document “Inverter Compatibility

Matrix” which is available from the official ABB website ( http://www.abb.

com/solarinverters ) in the Monitoring and Communication section

dentification of the equipment and manufacturer

The technical data provided in this manual does not substitute the data

supplied on the labels affixed to the equipment.

The labels affixed to the equipment must NOT be removed, damaged, stained, hidden, etc.,

for any reason whatsoever.

The following information which is useful in identifying the product, is

printed on the printed circuit of the VSN300 Wifi Logger Card:

- Manufacturer's Trade Mark

- CE Marking (European Union)

- RCM Marking (Australia)

- FCC ID

The FCC ID is: X6W-3N16E when the device is assembled with the Wi-Fi

radio module supplied by Epcos

The FCC ID is: X6W-3N16M when the device is assembled with the Wi-

Fi radio module supplied by Murata

An FCC ID label is supplied and must be positioned where it is clearly visible on the outside

of the inverter in which the board is installed.

Contains FCC ID: X6W-3N16E

Contains FCC ID: X6W-3N16M

Содержание VSN300






































































Результаты поиска

Содержание VSN300

Отзывы:

ABB VSN300, Руководство по эксплуатации продукта, Страница: 13 / 69

Результаты поиска

Содержание VSN300

Отзывы: