ABB Terra 124 Скачать руководство пользователя страница 26

Страница: 26 / 54

5. If you use an Ethernet cable, make sure that the internet connection is available

for an approved service engineer and the network operating center of the

manufacturer.

6. Make sure that the cable slack is sufficient to guide the cables in the cabinet.

Refer to section

8.10.2

7. Prepare the foundation for the cabinet. Refer to section

5.3.1

5.2.2

Control the space and airflow around the cabinet

1. Make sure that the floor space agrees with the requirements. Refer to section

8.10.3

2. Make sure that the air flow inlet and outlet cannot get blocked. Think of snow or

objects.

5.3

Prepare the foundation

5.3.1

Prepare the foundation - general procedure

1. Select the correct foundation, based on the surface you install the cabinet on.

2. Embed the cables in the ground with or without a cable duct. Refer to the local

rules.

5.3.2

Prepare a standard prefab foundation

Preliminary requirements

•

Prefab foundation. Refer to section

8.10.4

Procedure

1. Make the foundation (A). Do one of

these steps:
•

Contact the manufacturer to order

the foundation for your EVSE.

Refer to section

1.12

•

Make the foundation according to

the specifications.

2. Dig the hole for the foundation (B). For

the specifications, refer to section

8.10.4

Caution: Make sure that the

top surface of the

foundation is above the

ground level, to prevent

intrusion of water.

3. Guide the cables to the locations (C).

4. Install the foundation in the hole.

5. Put the cables through the openings (D) in the foundation. Apply the full cable

slack.

6. Fill the foundation with gravel or another substance to prevent rodents to enter

the cabinet.

Installation

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды