ABB Terra 124 Скачать руководство пользователя страница 23

Страница: 23 / 54

Transport

4.1

Transport the EVSE to the site

A transport company delivers the EVSE close to the site. The movement of the EVSE

to its final location is your responsibility.
•

If you need to store the EVSE before installation, obey the ambient conditions

for storage. Refer to section

8.6

4.2

Transport the EVSE on the site

4.2.1

Hoist the cabinet

Preliminary requirements

The cabinet is unpacked.

Refer to section

5.4.1

•

Hoisting equipment,

including cables, swivel eye

bolts or bolts with lifting

loops. Refer to section

8.4

Note:

Risk of pinching or crushing, the cabinet is heavy

•

Make sure that the hoisting equipment can lift the cabinet safely.

Obey the safety instructions that apply to the hoisting equipment.

Take into account the dimensions, the mass and the center of gravity

of the EVSE. Refer to chapter

Caution:
•

Do not drop the cabinet.

•

Do not tilt the cabinet more than allowed. Refer to section

8.9

Procedure

1. Install the swivel eye bolts or bolts

with lifting loops (A).

2. Connect the cables (B) of the hoisting

equipment to the swivel eye bolts or

bolts with lifting loops.

3. Move the cabinet to the correct

location.

Transport

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды