ABB Terra 124 Скачать руководство пользователя страница 40

Страница: 40 / 54

8.5

Torque specifications

Parameter

Specification [Nm]

Fasteners for the PE wire

Between 33 and 44

Fasteners for the L1, L2, L3 and neutral

wire

Between 33 and 44

8.6

Ambient conditions

Parameter

Specification

Environment, general

Indoor and outdoor

Storage temperature

-40°C to +70°C

Temperature during use

-35°C to +50°C

Maximum altitude above sea level

2500 m

Temperature derating

40°C

8.7

Mass and center of gravity

Mass

Mass

Specification

Cabinet

The type plate shows the specification.

Refer to section

2.1

Center of gravity

Location of center of gravity

Specification [mm]

207

385

1049

Note: The coordinates correspond with the agreements in section

1.15

0,0,0 is the left bottom front side of the EVSE.

8.8

Noise level

Noise level

Specification

Maximum noise level

< 62 dB(A)

Technical data

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды