background image

ABB | SACE Emax 2

Management operations

1 - Transport and checking on receipt

7 | © 2023 ABB |  1SDH001000R0002 - ECN000297030

Management operations

1 - Transport and checking on receipt

Introduction

The SACE Emax 2 circuit-breakers, on account of their weight, require special attention during transport 
and handling.
They are distributed with following packages:

•  one package for fixed circuit-breaker
•  two packages for withdrawable circuit-breakers (one package for the fixed part and one for the 

mobile part).

 

WARNING! comply with the following instructions during each transport phase:

• 

The movable part of the circuit-breaker must be removed from the switchgear and/or 

from the relative fixed part even if this latter is not installed in the switchgear.

• 

The circuit-breaker must be in the open position.

• 

The circuit-breaker must be protected and fastened in its original packing.

• 

The closing springs of the circuit-breaker must be completely discharged.

Weight of the circuit-breakers 

with packaging

The following table specifies the weights of the circuit-breakers with packaging:

Fixed

Moving part of withdra-

wable device

Fixed part of withdrawa-

ble device

III

IV

Fs

III

IV

Fs

III

IV

Fs

E2.2

46 Kg / 
101 lbs

58 Kg / 
128 lbs

53 Kg / 
117 lbs

60 Kg / 
132 lbs

41 Kg / 
90 lbs

49 Kg / 
108 lbs

E4.2

63 Kg / 
139 lbs

77 Kg / 
170 lbs

67 Kg / 
148 lbs

81 Kg / 
179 lbs

57 Kg / 
126 lbs

69 Kg / 
152 lbs

E6.2

118 Kg / 
260 lbs

134 Kg / 
295 lbs

151 Kg / 
333 lbs

129 Kg / 
258 lbs

143 Kg / 
315 lbs

159 Kg / 
350 lbs

96 Kg / 
212 lbs

109 Kg / 
240 lbs

123 Kg / 
271 lbs

E2.2-A

50 Kg / 
110 lbs

63 Kg / 
139 lbs

59 Kg / 
130 lbs

68 Kg / 
150 lbs

39 Kg / 
86 lbs

46 Kg / 
101 lbs

E4.2-A

66 Kg / 
154 lbs

81 Kg / 
179 lbs

75 Kg / 
165 lbs

91 Kg / 
201 lbs

52 Kg / 
115 lbs

63 Kg / 
139 lbs

E6.2-A

126 Kg / 
278 lbs

143 Kg / 
315 lbs

159 Kg / 
351 lbs

147 Kg / 
324 lbs

163 Kg / 
359 lbs

180 Kg / 
397 lbs

88 Kg / 
194 lbs

100 Kg / 
220 lbs

110 Kg / 
243 lbs

 NOTE:

• 

weights are indicated with reference to the basic circuit-breakers including protection trip 
unit and its sensors, without terminals and without accessories.

• 

the weights of the fixed part of withdrawable circuit-breakers refer to the version with 
horizontal rear terminals.

Transport of the packaged  

circuit-breaker

Consult the table "Weight of the circuit-breakers with packaging" before proceeding with the transport.

 

WARNING! improper lifting can result in death, serious injury to persons and damage to 

the equipment. Never lift a circuit-breaker and/or a fixed part above other people.

 

IMPORTANT: The trained personnel in charge of handling and lifting must use appropriate 

safety equipment.

 

Содержание SACE Emax 2 E2.2

























































Отзывы: