ABB RTU560 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 10

ABB RTU560 Скачать руководство пользователя страница 2

RTU560



Connections and Settings
Communication Unit 560CMD11

Doc.-No.: 1KGT 150 765 V005 1

2

Serial Interface RS232C Mode

Pin

Signal

Input / Output

RJ45

1

8

Rx

Tx

RJ45

1

8

RJ45

1

8

Rx

Tx

Jack

1

DCD

Input

2

RxD

Input

3

TxD

Output

4

DTR

Output

5

GND

-

7

RTS

Output

8

CTS

Input

Shield

Connected with housing

Table 2: Serial Interface RS232C Mode

The interfaces are available on the RJ45 connect-
ors and designed for RS485. The bus is terminat-
ed by a 1 k

Ω resistor for the interfaces.

CP1 and CP2 Interface

At  the  CP1  and  CP2  interfaces  connected  to  an
USART  (universal  synchronous/asynchronous  re-
ceiver/transmitter)  different  UART  based  protocol
types can be used.

CPA and CPB Interface

The settings have to be done by the RTUtil560
configuration tool.
At the CPA and CPB interfaces different UART
character based protocol types can be used.

560CMD11 R0011

The communication interface CPB has two differ-
ent functions:



UART character based protocols



GPRS-Modem-Interface

Both functions are mutually exclusive.

GPRS-Modem (only R0011)

The settings have to be done by the RTUtil560
configuration tool.

The 560CMD11 R0011 provides a radio interface
via an integrated Quad-Band GSM/GPRS mo-
dem. For communication via the GSM/GPRS mo-
dem a pluggable SIM-Card is necessary.

The SIM-Card socket is placed below the Com-
pactFlash socket.

The Quad-Band modem is designed for following
frequencies and GSM nets:



GSM 850MHz max. 2Watt transmitting
power



E-GSM 900MHz max. 2Watt transmitting
power



DCS 1800MHz max. 1Watt transmitting
power



PCS 1900MHz max. 1Watt transmitting
power

At the housing (see Fig. 10) an antenna or anten-
na cable can be connected via a 50

Ω (high fre-

quency) SMA-RF-connector type.

Note:

Operating without a frequency tuned antenna can
be cause damage on the GPRS modem.

Following antennas are recommended:



560ANA01 bar (dipole) antenna
ABB number: 1KGT023600R0001



560ANA02 Wall-mount antenna connect-
ed by a 5mtr long coaxial cable
ABB number: 1KGT023700R0005



560ANA02 Wall-mount antenna connect-
ed by a 20mtr long coaxial cable ABB
number: 1KGT023700R0020

«
1
2
3
4
...
»

Содержание RTU560











Отзывы:

Нет отзывов