ABB RELION 650 SERIES Скачать руководство пользователя страница 63

Страница: 63 / 110

•

This mode is used for all LEDs that are used to indicate a disturbance. The LEDs will

stay in the last state after the disturbance run time until they are reset after a

defined time.

•

The timers are set in Parameter Setting tool in the function block LEDGEN.

IEC09000657-1-en.vsd

IEC09000657 V1 EN-US

Figure 45: LHMI: LED operation mode

6.1.2

LED operation modes

GUID-40B89A33-3C2D-488C-8932-F862E0C9F477 v3

Description of different operation modes for LEDs to be configured in Application

Configuration tool and Parameter Setting tool.

Six operation modes are listed in the drop down menu in Parameter Setting tool.

•

Follow-S

•

Follow-F

•

LatchedAck-F-S

•

LatchedAck-S-F

•

LatchedColl-S

•

LatchedReset-S

LED operation mode Follow-S

IEC08000395.vsd

= Steady

= Flash

Illumination =>

R
Y
G

IEC08000395 V1 EN-US

Figure 46: LHMI: LED operation mode Follow-S

Monitoring a signal with a LED is a simple mode, where the LED follows the signal state. More

than one signal per LED can be used when applicable. See

Figure 46

for the valid priority rules.

The LED illuminates always in steady state.

1MRK 511 284-UEN B

Section 6

Local HMI engineering

650 series

Engineering manual

Содержание RELION 650 SERIES














































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

ABB RELION 650 SERIES, Инструкция по эксплуатации, Страница: 63 / 110

Результаты поиска

Содержание RELION 650 SERIES

Отзывы: