ABB RELION 650 SERIES Скачать руководство пользователя страница 35

Страница: 35 / 110

IEC08000365-2-en.vsd

IEC08000365 V2 EN-US

Figure 16: PCM600: Set up a plant structure

Once a plant structure is built the name of each level in the structure should be renamed by the

names/identifications used in the grid. Use the right mouse button to build the plant structure

by selecting the elements from the context menu. Rename the level after insertion, using the

Rename possibility or the Object Properties.

Figure 16

shows the start of a project with two

IEDs placed but still not renamed.

The plant structure corresponds to the complete grid including the needed

IEDs.

Procedure to build a plant structure:

•

Right-click the plant structure and select

New and Create from Template ..., or

•

Right-click in the plant structure and select

New, General and select one of the elements

IED Group or Substation.

•

Click

View in the menu bar and select Object Types. Select the needed elements and drag

and drop them into the plant structure. Close the window if it does not close

automatically.

4.6.1

IEC 61850 naming conventions to identify an IED

SEMOD58409-38 v5

This section is only valid when the IEC 61850 standard is used for station bus communication.

According to the IEC 61850–6 clause 8.4, the SCL model allows two kinds of project

designation in the object properties.

•

A technical key is used on engineering drawings and for signal identifications. The

technical key is used within SCL for referencing other objects. Observe that name is a

relative identification within a hierarchy of objects.

•

A user oriented textual designation is contained in attribute desc. Attributes are not

allowed to contain carriage return, line feed or tab characters. The semantics of desc shall

also be relative within an object hierarchy.

PCM600 takes care of these two possibilities. The two possible signal designations are

available per object in the object properties for all hierarchical levels beginning with the

station as the highest level.

The technical key is automatically generated based on the rules and type specifications of IEC

61346 and the extended definitions done for substations by a technical committee. The

technical key is shown in the

Object Properties under SCL Technical Key or Technical Key.

1MRK 511 284-UEN B

Section 4

Setting up a project

650 series

Engineering manual

Содержание RELION 650 SERIES














































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

ABB RELION 650 SERIES, Инструкция по эксплуатации, Страница: 35 / 110

Результаты поиска

Содержание RELION 650 SERIES

Отзывы: