ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 125 / 176

background image

Checking the influence of synchronizing check (at three-pole reclosing)

1.

Check that the autorecloser for 3-phase operation function SMBRREC (79) is
operative, for example, by making a three-pole reclosing shot with the
synchronizing check condition.
Remove the SMBRREC (25) signal.

2.

Apply a fault causing three-phase trip and thereby a RI signal.

3.

Wait for the

tSync

time out limit.

Check that no reclosing is made.

Restoring equipment

After the tests, restore the equipment to normal or desired state. Check the following
items in particular:

1.

Check the operation counters.
Reset the counters to zero, if that is the user's preference. The counter reset
function is found on the local HMI under

Main menu/Clear/Clear counters/

SMBRREC(79,0->1)

2.

Restore settings that may have been modified for the tests back to normal.

3.

Disconnect the test switch, CB simulating arrangement and test circuits.
Reconnect any links or connection terminals, which may have been opened for
the tests.

4.

Reset indications, alarms and disturbance recordings.
Clearing of the disturbance report must be done via the Disturbance Handling in
PCM600.

6.8.2.5

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Control/SMBRREC(79,0->1)/X:SMBRREC

for the function,

or for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.8.3

Autorecloser for 1/3-phase operation STBRREC (79)

Verification of the automatic reclosing function STBRREC (79) for single and three-
phase reclosing attempt, can be considered to consist of two parts; one part to verify
the internal logic and timing of the function and one part to verify its interaction with
the protection system. This section deals with verification of the auto-reclosing
function itself. However, it is practical to start initiate the autoreclosing function by
activating a protection function, for example, by secondary injection tests.

1MRK 506 331-UUS A

Section 6

Testing functionality

117

Commissioning Manual

«
...
123
124
125
126
127
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: Bornack Страницы: 32

Бренд: U-Line Страницы: 3

matchline 50PP8421

Бренд: Philips Страницы: 2

MatchLine 46PP9527

Бренд: Philips Страницы: 2

MatchLine 46PP8621

Бренд: Philips Страницы: 2

MATCH LINE 55PP925

Бренд: Philips Страницы: 2

Magnavox 9P6444C

Бренд: Philips Страницы: 2

Magnavox 9P6040C

Бренд: Philips Страницы: 2

Magnavox 9P6044C

Бренд: Philips Страницы: 2

Matchline 41GR8840

Бренд: Philips Страницы: 22

MAGNAVOX MX5472C101

Бренд: Philips Страницы: 60

MAGNAVOX TP4830

Бренд: Philips Страницы: 48

Earth Leakage HGMP N60 Z

Бренд: Hyundai Страницы: 32

Бренд: GE Grid Solutions Страницы: 740

Flex 5150 Appliance

Бренд: VERITAS Страницы: 5

Бренд: Franklin Electric Страницы: 25

Бренд: RCA Страницы: 64

Бренд: Watts Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды