ABB Relion 615 series Скачать руководство пользователя

Страница: 98 / 136

Fault indication

Fault code

Additional information

Internal Fault

Conf. error,X130

Card in slot X130 is wrong type, is

missing or does not belong to the original

composition.

Internal Fault

Card error,X000

Card in slot X000 is faulty.

Internal Fault

Card error,X100

Card in slot X100 is faulty.

Internal Fault

Card error,X110

Card in slot X110 is faulty.

Internal Fault

Card error,X120

Card in slot X120 is faulty.

Internal Fault

Card error,X130

Card in slot X130 is faulty.

Internal Fault

LHMI module

LHMI module is faulty. The fault

indication may not be seen on the LHMI

during the fault.

Internal Fault

RAM error

Error in the RAM memory on the CPU

card.

Internal Fault

ROM error

Error in the ROM memory on the CPU

card.

Internal Fault

EEPROM error

Error in the EEPROM memory on the

CPU card.

Internal Fault

FPGA error

Error in the FPGA on the CPU card.

Internal Fault

RTC error

Error in the RTC on the CPU card.

Internal Fault

RTD card error,X130

RTD card located in slot X130 may have

permanent fault. Temporary error has

occurred too many times within a short

time.

7.2.2

Warnings

Warnings are indicated with the text

Warning

additionally provided with the

name of the warning, a numeric code, and the date and time on the LHMI. The
warning indication message can be manually cleared.

If a warning appears, record the name and code so that it can be provided to ABB
customer service.

Section 7

1MRS756708 C

Troubleshooting

615 series

Operation Manual

Содержание Relion 615 series








































































































































Результаты поиска

Содержание Relion 615 series

Отзывы:

Похожие инструкции для Relion 615 series

Бренды по названию

Популярные бренды

ABB Relion 615 series, Руководство по эксплуатации

Результаты поиска

Содержание Relion 615 series

Отзывы:

Похожие инструкции для Relion 615 series

Бренды по названию

Популярные бренды