Quick Start Guide For The DNP Orion To ABB REL 356 Relays Using Modbus
8
8.
The ORION unit allows the operator to configure the unit by connecting an IBM compatible PC RS
232 port via a cable. Attach the RS 232 cable to the ORION DIAGNOSTIC PORT as shown in Figure
2, illustration 7 or Figure 2A illustration 7 depending upon unit selected.
9.
SOFTWARE CONFIGURATION: Supplied with the unit is a diskette with a file “ CTL2MOD.exe”.
This file configures the point mapping for the Conitel C300 to Modbus conversion. The Conitel
information varies from the format of Modbus and therefore the mapping of the two dissimilar
protocol’s points must occur. Place the file into the a directory within the personal computer. TYPE
“CTL2MOD” and depress the “ENTER KEY”.
10.
Use the arrow keys to scroll to the “Setup” Menu. Select the submenu titled PC –Prot Conv. The
following menu shall appear. Select the parameters as shown. The Port selection, however should
be modified to match your computer systems hardware configuration. After selection of all
parameters, simultaneously depress the “CONTROL and ENTER” key on the configuration terminal’s
keyboard.
+--------------¦ NovaTech Conitel-Modbus Configuration Program ¦---------------+
¦ PRINTER: READY FILE NAME: TEST.CTL ¦
¦ File Setup Memory Map Transfer About 10:37:06 ¦
¦¦¦¦¦¦¦¦¦+------------------------+¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦
¦¦¦¦¦¦¦¦¦¦ +-----------¦ Local PC Communication Setup ¦------------+¦¦¦¦¦¦¦¦¦¦¦¦
¦¦¦¦¦¦¦¦¦¦ ¦ ¦¦¦¦¦¦¦¦¦¦¦¦¦
¦¦¦¦¦¦¦¦¦¦ ¦ Port Baud Rate Parity Data Bits Stop Bits ¦¦¦¦¦¦¦¦¦¦¦¦¦
¦¦¦¦¦¦¦¦¦+-¦ (¦)COM1 ( )300 (¦)NONE ( )6 (¦)1 ¦¦¦¦¦¦¦¦¦¦¦¦¦
¦¦¦¦¦¦¦¦¦¦¦¦ ( )COM2 ( )600 ( )ODD ( )7 ( )2 ¦¦¦¦¦¦¦¦¦¦¦¦¦
¦+---------¦ ( )1200 ( )EVEN (¦)8 ¦----------+¦
¦¦Current V¦ ( )2400 ¦ ¦¦
¦¦ ¦ ( )4800 ¦ ¦¦
¦¦ ¦ (¦)9600 ¦ ¦¦
¦¦ ¦ ( )19200 ¦ ¦¦
¦¦ ¦ ¦ ¦¦
¦¦ ¦ ¦ ¦¦
¦¦ ¦ ¦ ¦¦
¦¦ +-------------------------------------------------------+ ¦¦
¦¦ ¦¦
¦¦ ¦¦
¦¦ ¦¦
¦¦ ¦¦
¦+-----------------------------¦ Message Window ¦-----------------------------+¦
+------------------------------------------------------------------------------+
<Tab>: Next Field <Esc>: Abort <Ctrl>+<Enter>: Accept
Figure 8 – Local PC Communication Setup Screen For The Orion DIAG Port.
11.
With the “SETUP” parameter highlighted, select the ProtConv Modbus Setup submenu selection,
until the following screen is displayed. The parameters listed in Figure 5 match those in the
protective device configuration (Step 7). After selection of all parameters, simultaneously depress the
“CONTROL and ENTER” key on the configuration terminal’s keyboard.
www
. ElectricalPartManuals
. com
