ABB LD 800HSE Скачать руководство пользователя страница 47

Страница: 47 / 136

Section 3 Configuration

Communication Settings

3BDD011677-600 A

Section 3 Configuration

Communication Settings

Although the linking device is delivered with a pre-configured IP address
(192.168.1.20), it must be assigned an IP address from your LAN address range.

Furthermore, subnet mask and gateway IP address must be set accordingly. This
information is referred to as IP configuration.

Table 10

shows the pre-configured IP settings of the linking device.

The IP configuration can be changed using one of the following methods:

Table 10. Pre-configured IP Settings

Parameter Name

Pre-configured value

Remark

Host Name

LD 800HSE

not used; you may leave this
unchanged or empty

IP Address

192.168.1.20

mandatory

Subnet Mask

255.255.255.0

mandatory

Maintenance IP
Address

192.168.1.21

recommended; for details
see

Network Configuration

on page 61

Broadcast Address

192.168.1.255

not used; it is automatically
adapted to the configured IP
address and subnet mask

Default Gateway

192.168.1.21

it is not necessary to config-
ure a default gateway, if the
host and the linking device
share the same network

Содержание LD 800HSE








































































































































Результаты поиска

Содержание LD 800HSE

Отзывы:

Бренды по названию

Популярные бренды

ABB LD 800HSE, Руководство пользователя

Результаты поиска

Содержание LD 800HSE

Отзывы:

Бренды по названию

Популярные бренды