ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 114

Страница: 114 / 199

ABB i-bus® KNX

PARAMETERS

7.4.100

Heat protection setpoint (building protection, cooling)

This parameter is used to define the setpoint temperature that must not be exceeded in the

Building

Protection cooling operating mode.

More information: → ⁠

Explanation of the operating modes, Page ⁠⁠174

Note

The temperature value specified here must be higher than the value in the parameter

Economy cooling

setpoint

If the device is in the

Cooling operating mode, the setpoint is active in the following cases:

• Controller receives the status "Window open", "Fill level alarm" or "Dew point alarm"
• The controller is deactivated via group object

Request On/Off (master)

• Controller is placed in the

Building Protection

operating mode via group objects

Operating mode nor-

mal (master)

Operating mode override (master)

Option

27 … 35 … 45 °C

Prerequisites for visibility

• Parameter window

Channel X

\ Parameter window

Application parameters

\ Parameter

Channel

function

\ Option

Controller channel

• The parameter is in the parameter window

Channel X

\ parameter window

Setpoint manager

7.4.101

Economy cooling setpoint

This parameter is used to define the setpoint temperature for the

Economy cooling operating mode.

More information: → ⁠

Explanation of the operating modes, Page ⁠⁠174

Note

The temperature value specified here must be higher than the value in the parameter

Standby cooling

setpoint

. A difference of at least 2 K is recommended.

Note

The controller ensures that the setpoint temperature is not fallen below when the actual temperature
decreases. The operating mode is not changed.

Option

10 … 29 … 40 °C

Prerequisites for visibility

• Parameter window

Channel X

\ Parameter window

Application parameters

– Parameter

Channel function

Option

Controller channel

– Parameter

Basic-stage heating [controller]

all options except

Deactivated

– Parameter

Option

Comfort, Standby, Economy, Building Protection

– Parameter

Setpoint specification and adjustment

Option

Absolute

• The parameter is in the parameter window

Channel X

\ parameter window

Setpoint manager

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

114

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы:

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 114 / 199

Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы: