manualshive.com logo in svg

ABB HT608505, Руководство по эксплуатации

Поделиться
Скачать
ABB HT608505 Скачать руководство пользователя страница 57

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.2 Cleaning the filter silencer

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.I

November 2021

Cleaning the absorption segments (81136)

u

Pull out and bend up the sheet-metal coverings (81137), and remove the absorption seg-
ments (81136).

u

Clean the absorption segments.
When cleaning, note that the absorption segments may only be cleaned lightly with pres-
surized air, a soft brush or a moist cleaning cloth.

u

Have any heavily contaminated absorption segments replaced by an ABB Turbocharging
Service Station.

Fitting the filter silencer

u

Insert the absorption segments (81136) into the sheet-metal coverings (81137).

u

Bend the sheet-metal coverings (81137) back to their original shape and insert into the
slotted guides in the filter silencer body (81135).

u

If the cleaning container is present on the filter silencer: Reinstall the water injection pipe.

 CAUTION

Penetration of dirt and foreign particles

Any penetration of dirt and foreign particles into the compressor can dam-
age it.

u

Fit the connecting rods (81269) correctly in the slots on the filter silencer
body (81135).

u

It must not be possible to rotate or move the cover grid (81266) after as-
sembly.

u

Check the position and alignment of the connecting rods during and after
assembly.

Fig. 27: Cleaning the filter silencer (2)

u

Place cover grids (81266) evenly and in the correct position.

u

Push connecting rods (81269) through the lugs of the cover grids (81266).

u

Connect the connecting rods (81269) with the screws (81272). When tightening the
screws (81272), make sure that the flattened ends of the connecting rods (81269) are cor-
rectly positioned on the edge of the filter silencer body (81135).

Page 

55

 / 

146

Содержание HT608505





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды