ABB HT603384 Скачать руководство пользователя страница 3

Страница: 3 / 146

Operation Manual / A170-M.. - A175-M..

Table of contents

HZTL4033_EN

Rev.G

December 2020

Operation Manual / A170-M.. - A175-M..

Introduction............................................................................................................ 4

1.1

Purpose of the manual................................................................................................. 4

1.2

Contact information...................................................................................................... 5

1.3

Essential information.................................................................................................... 5

1.4

Registered trademarks ................................................................................................. 5

1.5

Layout and function of the turbocharger ................................................................ 6

1.6

Symbols, definitions..................................................................................................... 8

1.7

Storage of new turbochargers and spare parts .................................................... 10

Safety .................................................................................................................... 12

2.1

Introduction .................................................................................................................. 12

2.2

CE conformity ............................................................................................................... 12

2.3

Definition of mandatory signs .................................................................................. 13

2.4

Definition of safety instructions .............................................................................. 13

2.5

Intended use ................................................................................................................. 14

2.6

Deflagration on gas engines ..................................................................................... 15

2.7

Periodic check of the pressure vessels.................................................................... 15

2.8

Warning plates on the turbocharger........................................................................ 16

2.9

Turbocharger rating plate.......................................................................................... 17

2.10

Lifting of loads ............................................................................................................. 19

2.11

Prerequisites for operation and maintenance...................................................... 20

2.12

Hazards during operation and maintenance ......................................................... 21

2.13

Safe operation .............................................................................................................. 23

2.14

Safe maintenance ....................................................................................................... 24

Removal and installation .................................................................................... 28

3.1

Turbocharger weight ................................................................................................. 28

3.2

Removing the turbocharger...................................................................................... 29

3.3

Installing the turbocharger ........................................................................................ 32

Commissioning .................................................................................................... 38

4.1

Oil supply ...................................................................................................................... 38

4.2

Inspection procedures ............................................................................................... 39

4.3

Commissioning after taking out of operation...................................................... 40

Monitoring during operation.............................................................................. 41

5.1

Oil pressure, oil temperature..................................................................................... 41

5.2

Turbocharger speed ................................................................................................... 43

Operation and service ......................................................................................... 46

6.1

Noise emission ............................................................................................................ 46

6.2

Service work ................................................................................................................. 48

Содержание HT603384



















































































































































Результаты поиска

Содержание HT603384

Отзывы:

Бренды по названию

Популярные бренды

ABB HT603384, Руководство по эксплуатации

Результаты поиска

Содержание HT603384

Отзывы:

Бренды по названию

Популярные бренды