ABB HT580667 Скачать руководство пользователя страница 97

Страница: 97 / 142

Operation Manual / 4 Product description / A130-M.. - A145-M..

8 Dismantling and fitting / 8.1 Introduction

HZTL4031_EN

Revision F

August 2017

Identification of the assembly devices

Not all assembly devices are marked with a part number. Identification is guaranteed by the
tool list. This list is enclosed in the toolbox.

WARNING

Servicing the assembly devices

Assembly devices must be checked for damage before and after use.

Visually inspect for corrosion, cracks, deformation and wear.

Damaged assembly devices must no longer be used and must be re-
placed.

Customer spare part set

Before starting operations, make sure the required customer spare part sets are available.

Oil orifice

When disassembling the turbocharger, an oil orifice fitted in the oil inlet must not be re-
moved (see also chapter

Removing the cartridge group

→

Tightening torques for components of the turbocharger

The specified tightening torques of the screw fittings must be observed (

Table of tightening

torques

→

Tightening torques for assembly devices

Unless described otherwise, the screws and nuts of the assembly devices supplied by ABB
must be tightened so they rest firmly against the surface.

Page

111

Содержание HT580667















































































































































Результаты поиска

Содержание HT580667

Отзывы:

Бренды по названию

Популярные бренды

ABB HT580667, Руководство по эксплуатации

Результаты поиска

Содержание HT580667

Отзывы:

Бренды по названию

Популярные бренды