ABB HT576419 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 121

background image

Operation Manual / TPL65-A32 / -A33 / -A36 + TPL69-A32 / -A33

8 Disassembly and assembly / 8.7 Installing cartridge group

© Copyright 2018 . All rights reserved.

HZTL2498_EN

Revision C

April 2018

8.7 Installing cartridge group

CAUTION

Oil orifice plates

An orifice plate for adjusting the oil pressure is fitted in each of the two
oil inlet channels in the bearing casing. When the cartridge group, the
bearing casing or the turbocharger is fitted to the engine, it must be
ensured that the orifice plates that are specified for the turbocharger
have been installed in the two oil inlet channels.

u

Check correct installation of oil orifice plates.

Fig. 2

u

Remove cover from oil connection.

u

Secure separate lifting gear to each of two ribs on bearing casing
provided for this purpose.

u

Remove supports (90450) and carefully insert cartridge group.

TPL65-A32/33/36

u

Evenly tighten the three screws (61059) together with Verbus Ripp®
washers (61058) to the specified tightening torque (see chapter Table
of tightening torques).

TPL69-A32/33

u

Evenly tighten screw (61059) together with Verbus Ripp® washers
(61058) and two nuts (61037) to the specified tightening torque (see
chapter Table of tightening torques).

Page

90

/

118

«
...
90
91
92
93
94
...
»

Содержание HT576419


























































































































Отзывы:

Нет отзывов

Похожие инструкции для HT576419

Бренд: Walker Bay Страницы: 8

Бренд: Obdstar Страницы: 10

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Datavideo Страницы: 28

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: ZOLL Страницы: 48

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Бренд: Rigol Страницы: 12

CHIEFTAIN E1006

Бренд: Falcon Страницы: 5

Бренд: Masalta Страницы: 13

Бренд: Taurus Страницы: 38

Бренд: Phonocar Страницы: 12

Бренд: Spokey Страницы: 4

Бренд: Fillauer Страницы: 12

Бренд: Hoshizaki Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды