ABB HT574962 Скачать руководство пользователя страница 68

Страница: 68 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

5 Operation and service / 5.4 Stopping the engine

HZTL4030_EN

Revision D

May 2017

Influencing parameters

The specified values are guideline values and are not guaranteed. The actual values can devi-
ate considerably from the guideline values, for example, due to the following influences:

Fuel quality and fuel treatment

Load profile (thermal cycling, also number of starts/stops, emergency shutdowns, oper-
ating point)

Gas inlet temperature

Turbocharger specification.

System-specific operating conditions (combustion quality, exhaust gas composition)

For bearing parts

Lubricating oil quality (oil filtering, oil condition, oil monitoring)

Load profile (speed, pressure conditions, temperature)

Number of starts/stops

Unbalance of the rotor (degree of contamination).

5.4

Stopping the engine

CAUTION

Residual heat in the turbocharger

If the residual heat in the turbocharger is not adequately dissipated, it may
damage the engine.

Adequate cooling of the turbocharger must be ensured after stopping
the engine.

Water-cooled turbocharger variant

Post-lubricate as long as the rotor is turning.

Observe the oil pressure while performing post-lubrication: 0.5 < p

oil

≤1.0.

Switch off post-lubrication as soon as the rotor is stationary or after no more than two
minutes.

Deviating procedures must be coordinated with ABB Turbo Systems.

Page

Содержание HT574962



























































































































Результаты поиска

Содержание HT574962

Отзывы:

Бренды по названию

Популярные бренды

ABB HT574962, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание HT574962

Отзывы:

Бренды по названию

Популярные бренды