ABB Endura AZ25 Series Скачать руководство пользователя страница 13

Страница: 13 / 40

Endura AZ25 series probe

Combustion oxygen monitor

3 Mechanical installation

OI/AZ25P–EN Rev. E

3.5.4 Pneumatic connection configurations

The pneumatic configuration of each probe is detailed on the probe identification label – see Section 3.3, page 7.

To identify the pneumatic configuration of your probe:

1. Remove the probe head cover and refer to the product code on the probe identification label to determine if restrictors are

fitted / not fitted:

–

code AZ25/X.X.X.1... = no restrictor fitted

–

code AZ25/X.X.X.3... = restrictor fitted

2. Refer to the flowchart below (Fig. 3.6) to identify which configuration is the closest match for your system and refer to the

relevant figure in Sections 3.5.5 (page 12) to 3.5.7 (page 13) for flow rates.

Fig. 3.6 Pneumatic connection configurations (schematic)

AZ25/X.X.X.1.X.........

AZ25/X.X.X.3.X.........

KEEP

TIGHTLY

CLOSED

WHEN NOT

IN USE

REF

AIR

3KS0000000/067

AZ25/XXXXXXXXXXXXX

Serial No

Code No

I/P

–

THC

–

*Is probe

fitted with a

restrictor?

Yes

*Is probe

connected to

AutoCal?

Yes

Reference

air supply

ABB air pump

Refer to the product code on the

probe data label (inside the probe

head) to identify system configuration

*Is probe

connected to

AutoCal?

ABB filter / regulator

See

Fig. 3.7

page 12

See

Fig. 3.12

page 14

Reference

air supply

Yes

*Is probe

connected to

AutoCal?

*Is probe

connected to

AutoCal?

See

Fig. 3.11

page 14

See

Fig. 3.8

page 12

See

Fig. 3.9

page 13

See

Fig. 3.10

page 13

See

Fig. 3.11

page 14

See

Fig. 3.12

page 14

Flowmeters not required

(test gases

must

be applied as pressure)

Flowmeters required

(test gas flow

must

be regulated by flowmeters)

Yes

ABB air pump

ABB filter / regulator

Endura AZ25 probe

(probe shown with cover removed)

Restrictor not fitted

Restrictor fitted

Содержание Endura AZ25 Series









































Результаты поиска

Содержание Endura AZ25 Series

Отзывы:

Похожие инструкции для Endura AZ25 Series

Бренды по названию

Популярные бренды

ABB Endura AZ25 Series, Руководство пользователя

Результаты поиска

Содержание Endura AZ25 Series

Отзывы:

Похожие инструкции для Endura AZ25 Series

Бренды по названию

Популярные бренды