ABB ELK-CT0 145 F Скачать руководство пользователя страница 4

4

CU R R E NT  TR A N S FOR M E R S  E LK- C T0 

I N S T R U C T I O N S  FO R  I N S TA L L AT I O N ,  USE  A N D  M A I N T EN A N C E

14) 

parameters of 1st core 

15) 

parameters of 2nd core 

16) 

parameters of 2nd core 

17) 

parameters of 3rd core 

18) 

parameters of 3rd core 

19) 

additional specification if required 

20) 

order number 

21) 

PTB marking (if required) 

22) 

length of sec. outlets (if required) 

3. Instructions for installation

General informations

Instrument transformer is electrical equipment 
and the electrical installation of the instrument 
transformer can be done by skilled personnel 
only. The level of experience, age and eligibility 
criteria for persons working with, on or near elec-
tric installations is governed by national legisla-
tion. If no asuch eligibility legislation is available 
the corresponding requirements can be found in 
EN 50110-1 standard. 

Safety instructions

1.  Always consider the transformer as a part of 

electric circuit which it is connected to. Don´t 
touch incoming connectors and terminals, or 
any other parts of the transformer, except you 
know for sure these are earthed. 

2.  Ground always the metallic base of the instru-

ment transformer. 

3.  Always connect one terminal of each secondary 

winding of the transformer to the earth. When 
the secondary of transformer is intercon-
nected, there should be only one grounded 
point to prevent accidental paralleling with sys-
tem grounding wire. 

4.  Always short-circuit the secondary of the cur-

rent transformer that is not currently in use, to 
prevent secondary voltages, which may be haz-
ardous to personnel or damaging to the trans-
former’s secondary. The secondary like this 
must be additionally grounded. 

Mounting

Transformers ELK-CT0 are designed as low-volt-
age current transformers 0.72/3kV, without built 
in primary conductor. Primary conductor is not in-
cluded in supply. 

Transformers ELK-CT0 are designed for mounting 
in gas-insulated switchgears type ELK-04. De-
pending on the protection concept they can be 

arranged in front or behind of the circuit break-
er’s interrupting unit. The primary sided insula-
tion is provided by SF

6

-gas. Up to a rated nominal 

current of 3 150 A current transformers are usu-
ally integrated into the flanges of the circuit 
breaker enclosure. Note, in case of a rated nomi-
nal current of 4 000 A a separate current trans-
former is required. All current transformers are 
casted on a support which is required to fix the 
current transformer in the enclosure. By that, the 
distance to the high voltage loaded conductors is 
guaranteed even in the case of a short circuit (and 
consequently high magnetic forces). The termi-
nals of the secondary windings are interfaced to 
the substation via a terminal box consisting of a 
multiple bushing disk and terminal blocks. Before 
installation of transformer into enclosure all sur-
faces have to be cleaned from dust, grease and 
other impurities, see 5. maintenance instructions. 

Connection of transformer primary side

The ELK-CT0 transformers don´t have their own 
primary conductor. If ELK-CT0 transformers will 
be used in other applications than ABB ELK-04 
Gas-Insulated Switchgear please contact us for 
support.

Connection of transformer secondary side

The transformers ELK-CT0 contains outlet cable 
with defined length for each type. Outlet cables 
are ended with cable lugs M6. If not specified oth-
erwise in the order, the cable cross-section may 
not exceed 6 mm

2

. The interface of the current 

transformer to the terminal box is handled with 
stranded wire connected to gas-to-air bushings 
with 60 pins (M6x12/15) to the outer environ-
ment. Depending on the number of wires either 
one or two gas-to-air bushings are available. The 
ends of the windings of all cores are correspond-
ingly identified.This identification may be 
changed by customer after agreement with man-
ufacturer.

Outlets designation


02


02  Example of outlets 
designation

Содержание ELK-CT0 145 F














Отзывы: