ABB EL6010 Скачать руководство пользователя страница 26

Страница: 26 / 76

EL6010 Gas Analyzer in Category 2G Operator’s Manual

42/24-30 EN Rev. 1

Chapter 4

Start the Gas Analyzer

CAUTION!

If the EL6010-... analyzer unit must be opened for operation or maintenance,
the instructions on the following warning label (affixed to the housing) must
be observed:

“

Before opening, disconnect power and wait 10 minutes!

”

For operation of the EL6010-CU control unit the following warning instruc-
tion must be observed:

“

Do not open when an explosive atmosphere may

be present!

”

Check the Installation

Make sure the EL6010 gas analyzer is correctly installed before carrying out any
start-up procedures.

Use the following check list:

Check

Installation site

•

Do the conditions at the installation site (zone rating, explosion group,

temperature class) match the information on the identification plate?

•

Are the control unit and the analyzer unit not installed outdoors?

•

Are the control unit and the analyzer unit securely fastened?

Operation with sample gases at positive pressures

•

Is the device version designed for operation with sample gases at

positive pressures? The identification plate should read: “See Special
Conditions for Sample Gas Pressure”.

Connection of gas lines

•

Are all gas lines correctly connected?

•

Is the pressure sensor connection not joined with the sample gas path?

Potential compensation connection

•

Is the external potential compensation connection of the analyzer unit

connected to the local potential compensation point?

•

Is the external potential compensation connection of the control unit

connected to the local potential compensation point?

Continued on next page

Содержание EL6010













































































Результаты поиска

Содержание EL6010

Отзывы:

Похожие инструкции для EL6010

Бренды по названию

Популярные бренды

ABB EL6010, Руководство оператора

Результаты поиска

Содержание EL6010

Отзывы:

Похожие инструкции для EL6010

Бренды по названию

Популярные бренды