ABB EasyLine EL3020 Скачать руководство пользователя страница 15

Страница: 15 / 136

Preparation for Installation

Material Required for the Installation (not supplied)

Gas Connections



For the connection of pipelines: Threaded connections with a 1/8 NPT

thread and PTFE sealing tape
Fidas24: Use only metal threaded connectors!

Fidas24: Gas lines

Process gases, test gases and waste air



PTFE or stainless steel tubes with 4 mm inside diameter and

PTFE or stainless steel tube with at least 10 mm inside diameter for
waste air



Tube

fittings



Pressure

regulator



Flow restrictor in the combustion gas supply line (see page 29)



Shut-off valve in the combustion gas supply line (see page 29)

Sample gas



Heated sample gas line (recommended: TBL 01) or

unheated sample gas line (PTFE or stainless steel tube with
inside/outside diameter 4/6 mm).
The fittings and O-rings required for the connection are included in
the scope of supply and delivery of the gas analyzer.

Flowmeter/Flow Monitor



Flowmeter or flow monitor with a needle valve for adjustment and

monitoring of the sample gas flow rate and purge gas flow rate if
required



Notes for the selection and use of flowmeters:



Measuring range 7…70 l/h



Pressure drop < 4 hPa



Needle valve open

Recommendation: Flowmeter 7…70 l/h, Part Number 23151-5-
8018474

Содержание EasyLine EL3020









































































































































Результаты поиска

Содержание EasyLine EL3020

Отзывы:

Похожие инструкции для EasyLine EL3020

Бренды по названию

Популярные бренды

ABB EasyLine EL3020, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание EasyLine EL3020

Отзывы:

Похожие инструкции для EasyLine EL3020

Бренды по названию

Популярные бренды