ABB Aztec 600 Color Скачать руководство пользователя | Manualshive

Страница: 81 / 110

background image

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate

Single- and multi-stream colorimetric analyzers

Appendix B

–

Troubleshooting

IM/AZT6CR–EN Rev. R

79

Appendix B

–

Troubleshooting

B.1 Analyzer Malfunction

In the majority of cases any problems experienced are usually
associated with the chemistry and the liquid handling section.

Check mechanical components that are involved with the liquid
handling  systematically.  For  example,  check  pumps,  valves,
tubing  and  tubing  connections  for  correct  operation  and  for
leaks or  blockages that change  the chemical  conditions  within
the analyzer.

A calibration fail can be caused by almost any part of the liquid
handling section of the analyzer, including the solutions.

Measurement variations may be due to air bubbles within the
sample entering the measurement cell or particulates causing
restrictions within the analyzer sample tubing and valve block.

Any unpredictable problems may be due to the standard or
reagent solutions or their flow through the analyzer. If any doubts
exist regarding the integrity of these solutions, replace with new
solutions in the early stages of the fault finding investigations.
Ensure reagent solutions are connected correctly and are within
their expiry date.

B.2 Cell Diagnostics

Within the Cell Diagnostics (see Section 10.2, page 54),
operation of the analyzer can be controlled manually.

This mode is used to check the basic performance of the
analyzer, such as the operation of the piston assembly, the
activation of valves and the general fluid handling.

It also displays the detector output in real time, allowing the
checking of the LED light source and the response of the
detector.

B.3 Effects of Loss of Power to the Analyzer

The automatic action taken by the analyzer following loss of
power is dependent upon the length of time the power was off.

Table B.1 shows the automatic functions performed:

Caution.

Check that there have been no unauthorized

modifications, for example, incorrect tubing fitted.

Analyzer

Status

Period of Loss of Power

< 6 hours

> 6 hours

During
measurement,
calibration or
cleaning

Function:

1. Piston resets

2. Analyzer

performs a prime
routine

3. Analyzer

performs a
calibration

4. Analyzer goes

into
measurement

Analyzer analog
outputs are held at the
last output levels prior
to the loss of power.

Analyzer relay outputs
are re-evaluated after
power restoration on
the basis of current
operating conditions.

The measurement
display retains the last
value recorded before
loss of power.

Function:

1. Piston resets

2. Analyzer performs a

prime routine

3. Analyzer performs a

calibration

4. Analyzer goes into

measurement

Analyzer analog outputs
are reset to minimum.

Analyzer relay outputs are
re-evaluated after power
restoration on the basis of
current operating
conditions.

The measurement display
resets (is blank) until a new
measurement is
completed.

Table B.1 Automatic Functions by Status/Power Loss

«
...
79
80
81
82
83
...
»

Содержание Aztec 600 Color















































































































Отзывы:

Нет отзывов

Похожие инструкции для Aztec 600 Color

Бренд: Larson Davis Страницы: 536

Бренд: QUBINO Страницы: 2

Бренд: Yamaha Страницы: 98

Бренд: X-laser Страницы: 17

Solicap M FTI55

Бренд: Endress+Hauser Страницы: 92

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

PASPORT PS-2174

Бренд: PASCO Страницы: 4

Бренд: Unipro Страницы: 2

Бренд: Hach Страницы: 4

Бренд: 365SMART Страницы: 20

Бренд: Roland Страницы: 224

Бренд: jbc Страницы: 12

Бренд: Apera Страницы: 2

Бренд: VOLTCRAFT Страницы: 4

Бренд: Kurzweil Страницы: 35

Cobra SMARTsense Chloride Ion

Бренд: PHYWE Страницы: 4

Бренд: Bamo Страницы: 2

Druck DryTC 165

Бренд: Baker Hughes Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды