ABB Aztec 600 Color Скачать руководство пользователя

Страница: 58 / 110

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate

Single- and multi-stream colorimetric analyzers

12 Diagnostic Information and Icons

IM/AZT6CR–EN Rev. R

12 Diagnostic Information and Icons

12.1 Analyzer Diagnostic Information

The analyzer is programmed to display diagnostic messages to
provide information on servicing requirements and any other
conditions that develop during operation.

All diagnostic messages displayed on the analyzer are added to
the analyzer's audit log.

Table 12.1 shows icon types, diagnostic messages and ON/OFF
status for the relays.

Note.

The diagnostic icons in the following table conform to

NAMUR 107.

Diagnostic Icon

NAMUR Status

Failure

Check function

Out of specification

Maintenance required

Icon

Diagnostic message

Stop

Relay

Attention

Relay

Calibration

Relay

Failure

Relay

Monitor in Service

The analyzer is measuring correctly.

OFF

20 Character User-defined Alarm Tag

User-defined alarm message.

–

Monitor Stopped

Analyzer operation has been stopped by the user.

OFF

Monitor Off

Analyzer operation has not been started or a failure has caused the
analyzer to stop operation and switch off all services.

OFF

OFF*

Calibrating

A calibration routine is being run.

OFF

A/D Error

A hardware error exists on the main board.

Power the analyzer down, wait for 10 seconds and power-up again.

If the error still exists contact the local ABB representative

OFF

*Relay status shows ON if a failure has caused the stoppage.

Table 12.1 Diagnostic Information, Relay Operations and Inhibits (Sheet 1 of 5)

Содержание Aztec 600 Color















































































































Результаты поиска

Содержание Aztec 600 Color

Отзывы:

Похожие инструкции для Aztec 600 Color

Бренды по названию

Популярные бренды

ABB Aztec 600 Color, Руководство пользователя

Результаты поиска

Содержание Aztec 600 Color

Отзывы:

Похожие инструкции для Aztec 600 Color

Бренды по названию

Популярные бренды