ABB AWIN GW120 Скачать руководство пользователя страница 60

Страница: 60 / 76

MODBU S EXCEPTIO N CODES

TROU BLES HO OTING

4JNO0 0030 8 A

Problem

Solution

Device is stuck in handshak-

ing state

Reboot the device stuck in handshaking state. If not possible, then reform

network or power cycle the gateway.

Note

: Power cycling the gateway or reforming the network will force all de-

vices to drop off the network and reconnect. This will impact network

availability.

Error Retrieving AP Mote
Data From Network Manager

Wait for System Recovery to automatically initiate system recovery. It is of-

ten seen during the boot up process. If this error is persistent after 10+

minutes of boot up then a power cycle may be required.

Network Manager Has Reset.

Wait for System Recovery to automatically initiate system recovery. It is of-

ten seen during the boot up process or during network configuration. If

this error is persistent after 10+ minutes of boot up then a power cycle

may be required.

8.3

Modbus Exception Codes

The following exception codes are supported.

Table 16: Exception codes

Exception code

Meaning

0x01 ILLEGAL_FUNCTION

No request bytes present.

0x02 ILLEGAL_DATA_ADDRESS

Starting address does not exist in mapping.

0x03 ILLEGAL_DATA_VALUE

Starting register valid, but length of requests spans at least one un-

mapped register.

WirelessHART device is disconnected in simplified in mapping.

0x06 SLAVE DEVICE BUSY

Slave is engaged in processing another command. Retry later.

This can happen when:

–

The data is stale. This can be either because the data is old, or be-
cause the device is responding with a non-successful response
code.

–

There is an update to the Modbus mapping in progress.

0x0b GATEWAY TARGET DEVICE

FAILED TO RESPOND

Indicates that no response was obtained from the target device.

This can happen when:

–

Device is disconnected.

–

Sending request to WirelessHART network failed.

To avoid Modbus exception notification, read each individual device data inde-

pendently. In a case of device disconnection, if you try to read data from multi-

ple devices in one block read, it will result in complete Modbus block read error.

Содержание AWIN GW120













































































Результаты поиска

Содержание AWIN GW120

Отзывы:

Похожие инструкции для AWIN GW120

Бренды по названию

Популярные бренды

ABB AWIN GW120, Руководство пользователя

Результаты поиска

Содержание AWIN GW120

Отзывы:

Похожие инструкции для AWIN GW120

Бренды по названию

Популярные бренды