ABB AMXE160 Скачать руководство пользователя страница 5

Страница: 5 / 34

InTroduCTIon

1. Introduction

1.1. General

The purpose of this document is to describe general guidelines for the installation, maintenance and
disposal of the AMXE160 motor.

• Actions shown in this manual are only to be performed by trained personnel authorized by ABB or

authorized by the end user.

The actual appearance of the motor may vary from the illustrations in this manual, depending on the final
design.

Abbreviations and nomenclature used in this manual:

• D-end or DE: Drive side of motor.

• ND-end or NDE: Non drive side of motor.

• WARNING: signal word used to indicate a potentially hazardous situation which, if not avoided, can

result in death or serious injury.

Symbols used in this manual:

Motors for heavy electrical vehicles, type AMXE132

Introduction

3BSY600011-BCM

6 (34)

Chapter 1

Introduction

1.1

General

The purpose of this document is to describe general guidelines for the installation, maintenance

and disposal of the AMXE132 motor.

•

Actions shown in this manual are only to be performed by trained personnel authorized by

ABB or authorized by the end user.

The actual appearance of the motor may vary from the illustrations in this manual, depending on

the final design.

Abbreviations and nomenclature used in this manual:

•

D-end or DE: Drive side of motor.

•

ND-end or NDE: Non drive side of motor.

•

WARNING: signal word used to indicate a potentially hazardous situation which, if not

avoided, can result in death or serious injury.

Symbols used in this manual:

Caution, risk of electric shock.

Safety Alert Symbol, warns of a potential personal injury hazard.

Warning, magnetic field.

Prohibition, No access for people with active implanted cardiac devices

(pace maker)

Caution, risk of electric shock.

Motors for heavy electrical vehicles, type AMXE132

Introduction

3BSY600011-BCM

6 (34)

Chapter 1

Introduction

1.1

General

The purpose of this document is to describe general guidelines for the installation, maintenance

and disposal of the AMXE132 motor.

•

Actions shown in this manual are only to be performed by trained personnel authorized by

ABB or authorized by the end user.

The actual appearance of the motor may vary from the illustrations in this manual, depending on

the final design.

Abbreviations and nomenclature used in this manual:

•

D-end or DE: Drive side of motor.

•

ND-end or NDE: Non drive side of motor.

•

WARNING: signal word used to indicate a potentially hazardous situation which, if not

avoided, can result in death or serious injury.

Symbols used in this manual:

Caution, risk of electric shock.

Safety Alert Symbol, warns of a potential personal injury hazard.

Warning, magnetic field.

Prohibition, No access for people with active implanted cardiac devices

(pace maker)

Safety Alert Symbol, warns of a potential personal injury hazard.

Motors for heavy electrical vehicles, type AMXE132

Introduction

3BSY600011-BCM

6 (34)

Chapter 1

Introduction

1.1

General

The purpose of this document is to describe general guidelines for the installation, maintenance

and disposal of the AMXE132 motor.

•

Actions shown in this manual are only to be performed by trained personnel authorized by

ABB or authorized by the end user.

The actual appearance of the motor may vary from the illustrations in this manual, depending on

the final design.

Abbreviations and nomenclature used in this manual:

•

D-end or DE: Drive side of motor.

•

ND-end or NDE: Non drive side of motor.

•

WARNING: signal word used to indicate a potentially hazardous situation which, if not

avoided, can result in death or serious injury.

Symbols used in this manual:

Caution, risk of electric shock.

Safety Alert Symbol, warns of a potential personal injury hazard.

Warning, magnetic field.

Prohibition, No access for people with active implanted cardiac devices

(pace maker)

Warning, magnetic field.

Motors for heavy electrical vehicles, type AMXE132

Introduction

3BSY600011-BCM

6 (34)

Chapter 1

Introduction

1.1

General

The purpose of this document is to describe general guidelines for the installation, maintenance

and disposal of the AMXE132 motor.

•

Actions shown in this manual are only to be performed by trained personnel authorized by

ABB or authorized by the end user.

The actual appearance of the motor may vary from the illustrations in this manual, depending on

the final design.

Abbreviations and nomenclature used in this manual:

•

D-end or DE: Drive side of motor.

•

ND-end or NDE: Non drive side of motor.

•

WARNING: signal word used to indicate a potentially hazardous situation which, if not

avoided, can result in death or serious injury.

Symbols used in this manual:

Caution, risk of electric shock.

Safety Alert Symbol, warns of a potential personal injury hazard.

Warning, magnetic field.

Prohibition, No access for people with active implanted cardiac devices

(pace maker)

Prohibition, No access for people with active implanted cardiac devices (pace maker).

Содержание AMXE160



































Результаты поиска

Содержание AMXE160

Отзывы:

Похожие инструкции для AMXE160

Бренды по названию

Популярные бренды

ABB AMXE160, Руководство пользователя

Результаты поиска

Содержание AMXE160

Отзывы:

Похожие инструкции для AMXE160

Бренды по названию

Популярные бренды