manualshive.com logo in svg

ABB ACH400 Series, Руководство пользователя

Поделиться
Скачать
ABB ACH400 Series Скачать руководство пользователя страница 41

Chapter 4 – Start-up Procedure

4-2

ACH 400 with Electronic Bypass User’s Manual

Electronic Bypass 
Jumper, Switch and 
Pot Settings

Figure 4-1 shows the locations of the jumpers, DIP switch and potentiometer 
on the Electronic Bypass control board. The functions and settings of these 
items are explained in the following paragraphs.

Figure 4-1

Electronic Bypass Control Board

DIP Switch Settings

The DIP switch is used to configure the bypass overload protection and 
enable the automatic bypass feature.

Match the DIP Switch Codes to your drive model using Table 4-3.

Table 4-1

DIP Switch Settings

User Override Jumper

In the unlikely event of failure in the bypass control electronics, the user can 
put the bypass in the drive mode by moving jumper J2 to the position as 
shown in Figure 4-1. Power must first be applied to the system before placing 
the jumper in the User Override position. When the jumper is in the User 
Override position, the Drive contactor is energized and the Bypass contactor 
is deenergized. The contactors are not controlled by the Electronic Bypass 
keypad when the bypass is in the User Override mode.

Switch

Switch Setting Configurations

Overload protection configuration for frame size

Code

A

B

C

D

E

F

G

H

8 (A0)

OFF

ON

OFF

ON

OFF

ON

OFF

ON

7 (A1)

OFF

OFF

ON

ON

OFF

OFF

ON

ON

6 (A2)

OFF

OFF

OFF

OFF

ON

ON

ON

ON

5 (A3)

ON

ON

ON

ON

ON

ON

ON

ON

4 (A4)

OFF/ON = NEMA Class 30/NEMA Class 20

overload trip curve

3 (A5)

OFF/ON = Automatic Reset OFF/ON

2 (A6)

OFF/ON = Underload Protection Feature OFF/ON

1 (A7)

OFF/ON = Automatic Bypass Feature OFF/ON

ON

1  2  3  4  5  6  7  8

Dip Switch

Jumper J2

Normal

Setting

User Override

Setting

50

10

0

0

Potentiometer

R63

R64

Jumper

Wires

Jumper J3

110 VAC

POWERED

I/O

24 VDC

POWERED

I/O

Содержание ACH400 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды