ABB 7651 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

ABB 7651 Скачать руководство пользователя страница 13

11

3

MECHANICAL INSTALLATION…

Temperature
Compensator
Location

Measuring

Electrode
Location

Reference Chamber

Reference
Electrode
Location/Filling
Hole

Blanking Plug Fitted
in (ORP) Redox
Systems

Reservoir Tube Connector
(fitted if system is used
with reservoir)

Temperature
Compensator
(Blue Ring)

Reference
Electrode
(Black Ring)

Measuring
Electrode
pH, Redox
(Red Ring)

Ensure 'O' rings
are fitted

1

2

Tighten each cable
termination to
ensure a good seal.
See Note above

Connector
(Lower Section)

Connectors
(Upper Section)

Reassemble in the reverse order to that shown in the steps in Fig.
3.6 or Fig. 3.7. Before fitting the Top Cover, however, connect the
colour coded electrode cables to the appropriate electrodes –
see Fig. 3.11.

Finally, tighten the gland nut to secure the connecting cable.

3.4

Fitting the Reservoir – Models 7651, 7652, 7660

Fig. 3.10 Location of Blanking Plug and Reservoir Tube

Connector

Caution. It is vital that the terminations are kept dry at
all times.

Note. When fitting or removing the electrode
connectors, hold the top section of the connector
firmly while rotating the bottom section.

Fig. 3.11 Fitting the Electrode Connectors

«
...
11
12
13
14
15
...
»

Содержание 7651

























Отзывы:

Нет отзывов